- 您現在的位置：買賣IC網 > PDF目錄374311 > KBE00S009M-D411 (SAMSUNG SEMICONDUCTOR CO. LTD.) 1Gb NAND x 2 + 256Mb Mobile SDRAM x 2 PDF資料下載
參數資料
| 型號： | KBE00S009M-D411 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | 1Gb NAND x 2 + 256Mb Mobile SDRAM x 2 |
| 中文描述： | 1Gb的NAND × 2 256Mb的移動SDRAM × 2 |
| 文件頁數： | 38/86頁 |
| 文件大?。?/td> | 1898K |
| 代理商： | KBE00S009M-D411 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁
MCP MEMORY
38
KBE00S009M-D411
Revision 1.0
May 2005
READ STATUS
The device contains a Status Register which may be read to find out whether program or erase operation is completed, and whether
the program or erase operation is completed successfully. After writing 70h command to the command register, a read cycle outputs
the content of the Status Register to the I/O pins on the falling edge of CE or RE, whichever occurs last. This two line control allows
the system to poll the progress of each device in multiple memory connections even when R/B pins are common-wired. RE or CE
does not need to be toggled for updated status. Refer to table 4 for specific Status Register definitions. The command register
remains in Status Read mode until further commands are issued to it. Therefore, if the status register is read during a random read
cycle, a read command(00h or 50h) should be given before sequential page read cycle.
For Read Status of Multi Plane Program/Erase, the Read Multi-Plane Status command(71h) should be used to find out whether
multi-plane program or erase operation is completed, and whether the program or erase operation is completed successfully. The
pass/fail status data must be checked only in the Ready condition after the completion of Multi-Plane program or erase operation.
Table4. Read Staus Register Definition
NOTE
:
1. I/O 0 describes combined Pass/Fail condition for all planes. If any of the selected multiple pages/blocks fails in Program/
Erase operation, it sets "Fail" flag.
2. The pass/fail status applies only to the corresponding plane.
I/O No.
Status
Definition by 70h Command
Definition by 71h Command
I/O 0
Total Pass/Fail
Pass : "0" Fail : "1"
Pass : "0"
(1)
Fail : "1"
I/O 1
Plane 0 Pass/Fail
Must be don’t -cared
Pass : "0"
(2)
Fail : "1"
I/O 2
Plane 1 Pass/Fail
Must be don’t -cared
Pass : "0"
(2)
Fail : "1"
I/O 3
Plane 2 Pass/Fail
Must be don’t -cared
Pass : "0"
(2)
Fail : "1"
I/O 4
Plane 3 Pass/Fail
Must be don’t -cared
Pass : "0"
(2)
Fail : "1"
I/O 5
Reserved
Must be don’t -cared
Must be don’t-cared
I/O 6
Device Operation
Busy : "0" Ready : "1"
Busy : "0" Ready : "1"
I/O 7
Write Protect
Protected : "0" Not Protected : "1"
Protected : "0" Not Protected : "1"
Read ID
The device has 2 types of Read ID command, i.e. Read ID (1) command 90h and Read ID (2) command 91h.
The device contains a product identification mode, initiated by writing 90h to the command register, followed by an address input of
00h. Four read cycles sequentially output the manufacture code(ECh), and the device code (79h), Reserved(A5h), Multi plane oper-
ation code(C0h) respectively. A5h must be don’t-cared. C0h means that device supports Multi Plane operation. The command regis-
ter remains in Read ID mode until further commands are issued to it.
Read ID (2) command 91h provides Multi-Plane(4-Plane) operations availability. If ID code read out by 91h is 20h, it indicates the
device has Multi-Plane(4-Plane) operations.
Figure 19-1 & 19-2 show the operation sequence.
Figure 19-1. Read ID (1) Operation
CE
CLE
I/O
0
~
7
ALE
RE
WE
90h
00h
ECh
Address. 1cycle
Maker code
Device code
t
CEA
t
AR
t
REA
A5h
C0h
Multi-Plane code
t
WHR
71h
相關PDF資料 |
PDF描述 |
|---|---|
| KBJ2501 | 25A SINGLE PHASE SILICON BRIDGE RECTIFIER |
| KBJ2502 | 25A SINGLE PHASE SILICON BRIDGE RECTIFIER |
| KBJ2503 | 25A SINGLE PHASE SILICON BRIDGE RECTIFIER |
| KBJ2504 | 25A SINGLE PHASE SILICON BRIDGE RECTIFIER |
| KBJ2505 | 25A SINGLE PHASE SILICON BRIDGE RECTIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KB-E100SRW | 功能描述:LED 顯示器和配件 Red 640nm 90mcd Diffused Light Bar RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| KB-E100SURKW | 功能描述:LED條和陣列 8.89X3.81MM RED LT BAR LED DISPLAY RoHS:否 制造商:Avago Technologies 產品:LED Light Bars 照明顏色:Red 光強度:45 mcd 封裝:Tube |
| KBE1A11N | 制造商:Lovato Electric Inc 功能描述: |
| KBEV 5T-0.5-RSSV 4.5T | 制造商:TURCK Inc 功能描述:KBEV 5T-0.5-RSSV 4.5T |
| KB-F100SRW | 功能描述:LED 顯示器和配件 Red 640nm 200mcd Diffused Light Bar RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。