- 您現在的位置：買賣IC網 > PDF目錄16440 > CDB8420 (Cirrus Logic Inc)EVALUATION BOARD FOR CS8420 PDF資料下載
參數資料
| 型號： | CDB8420 |
| 廠商： | Cirrus Logic Inc |
| 文件頁數： | 81/94頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVALUATION BOARD FOR CS8420 |
| 標準包裝： | 1 |
| 主要目的： | 音頻，采樣率轉換器 |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | CS8420 |
| 主要屬性： | 帶數字音頻發射器和接收器的采樣率轉換器 |
| 次要屬性： | 44.1、48、96 kHz 輸出采樣率，AES/EBU，S/PDIF，EIAJ-340，GUI |
| 已供物品： | 板 |
| 相關產品： | 598-1125-5-ND - IC SAMPLE RATE CONVERTER 28SOIC |
| 其它名稱： | 598-1782 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁當前第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
82
DS245F4
CS8420
15.1.1
Manually Accessing the E Buffer
The user can monitor the data being transferred by reading the E buffer, which is mapped into the register
space of the CS8420, via the control port. The user can modify the data to be transmitted by writing to the
E buffer.
The user can configure the interrupt enable register to cause interrupts to occur whenever D-to-E or E-to-
F buffer transfers occur. This allows determination of the allowable time periods to interact with the E buff-
er.
Also provided are D-to-E and E-to-F inhibit bits. The associated buffer transfer is disabled whenever the
user sets these bits. These may be used whenever “l(fā)ong” control port interactions are occurring. They can
also be used to align the behavior of the buffers with the selected audio data flow. For example, if the
audio data flow is serial port in to AES3 out, then it is necessary to inhibit D-to-E transfers, since these
would overwrite the desired transmit C data with invalid data.
Flowcharts for reading and writing to the E buffer are shown in Figures 39 and 40. For reading, since a D-
to-E interrupt just occurred, then there a substantial time interval until the next D-to-E transfer (approxi-
mately 192 frames worth of time). This is usually plenty of time to access the E data without having to
inhibit the next transfer. For writing, the sequence starts after a E-to-F transfer, which is based on the out-
put timebase. Since a D-to-E transfer could occur at any time (this is based on the input timebase), then
it is important to inhibit D-to-E transfers while writing to the E buffer until all writes are complete. Then wait
until the next E-to-F transfer occurs before enabling D-to-E transfers. This ensures that the data written
to the E buffer actually gets transmitted and not overwritten by a D-to-E transfer.
If the channel status block to transmit indicates PRO mode, then the CRCC byte is automatically calcu-
lated by the CS8420, and does not have to be written into the last byte of the block by the host microcon-
troller.
block 1
block 2
block 3
block 4
block 5
block 1
block 2
block 3
block 4
block 5
Contents of E buffer
Updated at Fsi rate
Contents of F buffer
Updated from E
Output at Fso rate
Fso > Fsi (3/2) Causes blocks 1 and 3 to be transmitted twice
Fso < Fsi (2/3) Causes blocks 3 and 6 to not be transmitted
Contents of E buffer
Updated at Fsi rate
Contents of F buffer
Updated from E
Output at Fso rate
block 1
block 2
block 3
block 4
block 5
block 6
block 7
block 1
block 2
block 4
block 5
block 7
Figure 38. Channel Status Block Handling When Fso is Not Equal to Fsi
D to E interrupt occurs
Optionally set D to E inhibit
Read E data
If set, clear D to E inhibit
Return
Figure 39. Flowchart for Reading the E Buffer
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J11-EX | CONVERTER MOD DC/DC 12V 75W |
| GEM28DTAT | CONN EDGECARD 56POS R/A .156 SLD |
| 6278895-7 | C/A 62.5/125 RIS SC MTRJ 7M1 |
| A3BBB-2436G | IDC CABLE- ASR24B/AE24G/ASR24B |
| GSM12DTAN | CONN EDGECARD 24POS R/A .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CDB8421 | 功能描述:音頻 IC 開發工具 2-Ch 32-Bit 192kHz sample rate converte RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| CDB8422 | 功能描述:界面開發工具 Eval Bd 192kHz SRC S/PDIF Receiver RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| CDB8427 | 功能描述:音頻 IC 開發工具 Eval Bd 96kHz Dig. Audio Transcvr RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| CDB8952 | 制造商:Cirrus Logic 功能描述:NOT RECOMMENDED FOR NEW DESIGNS - USE CDB8952T - Bulk 制造商:Cirrus Logic 功能描述:Tools Development kit Kit Con |
| CDB8952T | 功能描述:以太網開發工具 Eval Bd 100BASE-TX/ 10BASE-T Transceiver RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。