- 您現在的位置：買賣IC網 > PDF目錄1905 > ATMEGA103-6AI (Atmel)IC MCU 128K 6MHZ A/D IT 64TQFP PDF資料下載
參數資料
| 型號： | ATMEGA103-6AI |
| 廠商： | Atmel |
| 文件頁數： | 83/141頁 |
| 文件大小： | 0K |
| 描述： | IC MCU 128K 6MHZ A/D IT 64TQFP |
| 產品培訓模塊： | megaAVR Introduction |
| 標準包裝： | 90 |
| 系列： | AVR® ATmega |
| 核心處理器： | AVR |
| 芯體尺寸： | 8-位 |
| 速度： | 6MHz |
| 連通性： | SPI，UART/USART |
| 外圍設備： | POR，PWM，WDT |
| 輸入/輸出數： | 32 |
| 程序存儲器容量： | 128KB（64K x 16） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大小： | 4K x 8 |
| RAM 容量： | 4K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4 V ~ 5.5 V |
| 數據轉換器： | A/D 8x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 64-TQFP |
| 包裝： | 托盤 |
| 配用： | ATSTK501-ND - ADAPTER KIT FOR 64PIN AVR MCU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁當前第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁
46
ATmega103(L)
0945I–AVR–02/07
When writing to one of the registers TCNT0, OCR0 or TCCR0, the value is
transferred to a temporary register and latched after two positive edges on TOSC1.
The user should not write a new value before the contents of the temporary register
have been transferred to its destination. Each of the three mentioned registers have
their individual temporary register, which means that e.g., writing to TCNT0 does not
disturb an OCR0 write in progress. To detect that a transfer to the destination
register has taken place, an Asynchronous Status Register (ASSR) has been
implemented.
When entering Power-save mode after having written to TCNT0, OCR0 or TCCR0,
the user must wait until the written register has been updated if Timer/Counter0 is
used to wake up the device. Otherwise, the MCU will go to sleep before the changes
have had any effect. This is extremely important if the Output Compare0 interrupt is
used to wake up the device; Output Compare is disabled during write to OCR0 or
TCNT0. If the write cycle is not finished (i.e., the user goes to sleep before the
OCR0UB bit returns to zero), the device will never get a compare match and the
MCU will not wake up.
If Timer/Counter0 is used to wake up the device from Power-save mode,
precautions must be taken if the user wants to reenter Power-save mode: The
interrupt logic needs one TOSC1 cycle to get reset. If the time between wake-up
and reentering Power-save mode is less than one TOSC1 cycle, the interrupt will not
occur and the device will fail to wake up. If the user is in doubt whether the time
before re-entering Power-save is sufficient, the following algorithm can be used to
ensure that one TOSC1 cycle has elapsed:
1.
Write a value to TCCR0, TCNT0 or OCR0.
2.
Wait until the corresponding Update Busy Flag in ASSR returns to zero.
3.
Enter Power-save mode.
When asynchronous operation is selected, the 32 kHz Oscillator for Timer/Counter0
is always running, except in Power-down mode. After a Power-up Reset or wake-up
from Power-down, the user should be aware of the fact that this Oscillator might take
as long as one second to stabilize. The user is advised to wait for at least one
second before using Timer/Counter0 after Power-up or wake-up from Power-down.
The content of all Timer/Counter0 Registers must be considered lost after a wake-
up from Power-down due to the unstable clock signal upon start-up, no matter
whether the Oscillator is in use or a clock signal is applied to the TOSC pin.
Description of wake-up from Power-save mode when the Timer is clocked
asynchronously: When the interrupt condition is met, the wake-up process is started
on the following cycle of the Timer clock, that is, the Timer is always advanced by at
least one before the processor can read the counter value. To execute the
corresponding Timer/Counter0 interrupt routine, the Global Interrupt bit in SREG
must have been set. Otherwise, the part will still wake up from Power-down, but
continues to execute the Sleep command. The Interrupt Flags are updated three
processor cycles after the processor clock has started. During these cycles, the
processor executes instructions, but the interrupt condition is not readable and the
interrupt routine has not started yet.
During asynchronous operation, the synchronization of the Interrupt Flags for the
asynchronous Timer takes three processor cycles plus one timer cycle. The Timer is
therefore advanced by at least one before the processor can read the Timer value
causing the setting of the Interrupt Flag. The Output Compare pin is changed on the
Timer clock, and is not synchronized to the processor clock.
After waking up from Power-save mode with the asynchronous Timer enabled, there
will be a short interval of which TCNT0 will read as the same value as before Power-
相關PDF資料 |
PDF描述 |
|---|---|
| ATMEGA128A-AUR | MCU AVR 128K FLASH 16MHZ 64TQFP |
| ATMEGA128L-8MJ | IC MCU AVR 128K 8MHZ LV 64-QFN |
| ATMEGA16-16MUR | MCU AVR 16KB FLASH 16MHZ 44QFN |
| ATMEGA164PA-AN | IC MCU AVR 16K FLASH 44TQFP |
| ATMEGA164PA-CUR | MCU AVR 16KB FLASH 20MHZ 49VFBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATMEGA103L | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 128K Bytes In-System Programmable Flash |
| ATMEGA103L-4AC | 功能描述:8位微控制器 -MCU TQFP-64 128K FLASH 3 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ATMEGA103L-4AI | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-Bit Microcontroller with 64K/128K Bytes In-System Programmable Flash |
| ATMEGA128 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 128K Bytes In-System Programmable Flash |
| ATMEGA128(L) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ATmega128(L) Preliminary Summary [Updated 9/03. 23 Pages] |
發布緊急采購，3分鐘左右您將得到回復。