- 您現在的位置：買賣IC網 > PDF目錄1905 > ATMEGA103-6AI (Atmel)IC MCU 128K 6MHZ A/D IT 64TQFP PDF資料下載
參數資料
| 型號： | ATMEGA103-6AI |
| 廠商： | Atmel |
| 文件頁數： | 18/141頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 128K 6MHZ A/D IT 64TQFP |
| 產品培訓模塊： | megaAVR Introduction |
| 標準包裝： | 90 |
| 系列： | AVR® ATmega |
| 核心處理器： | AVR |
| 芯體尺寸： | 8-位 |
| 速度： | 6MHz |
| 連通性： | SPI，UART/USART |
| 外圍設備： | POR，PWM，WDT |
| 輸入/輸出數： | 32 |
| 程序存儲器容量： | 128KB（64K x 16） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 4K x 8 |
| RAM 容量： | 4K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4 V ~ 5.5 V |
| 數據轉換器： | A/D 8x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 64-TQFP |
| 包裝： | 托盤 |
| 配用： | ATSTK501-ND - ADAPTER KIT FOR 64PIN AVR MCU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁
114
ATmega103(L)
0945I–AVR–02/07
As an alternative to using the RESET signal, PEN can be held low during Power-
on Reset while SCK is set to “0”. In this case, only the PEN value at Power-on
Reset is important. If a crystal is not connected across pins XTAL1 and XTAL2,
apply a clock signal to the XTAL1 pin. If the programmer cannot guarantee that
SCK is held low during power-up, the PEN method cannot be used. The device
must be powered down in order to commence normal operation when using this
method.
2.
Wait for at least 20 ms and enable serial programming by sending the Program-
ming Enable serial instruction to pin PE0(PDI/RXD).
3.
The serial programming instructions will not work if the communication is out of
synchronization. When in sync, the second byte ($53) will echo back when issu-
ing the third byte of the Programming Enable instruction. Whether the echo is
correct or not, all four bytes of the instruction must be transmitted. If the $53 did
not echo back, give SCK a positive pulse and issue a new Programming Enable
instruction. If the $53 is not seen within 32 attempts, there is no functional device
connected.
4.
If a chip erase is performed (must be done to erase the Flash), wait at least (2 x
t
WD_FLASH), give RESET a positive pulse of at least two XTAL1 cycles duration
after SCK has been set to “0”, and start over from step 2.
5.
The Flash is programmed one page at a time. The memory page is loaded one
byte at a time by supplying the 7 LSB of the address and data together with the
Load Program Memory Page instruction. The Program Memory Page is stored
by loading the Write Program Memory Page instruction with the 9 MSB of the
address. The next page can be written after t
WD_FLASH, i.e., writing 256 bytes
takes t
WD_FLASH. Accessing the serial programming interface before the Flash
write operation completes can result in incorrect programming.
6.
The EEPROM array is programmed one byte at a time by supplying the address
and data together with the appropriate Write instruction. An EEPROM memory
location is first automatically erased before new data is written. If polling is not
used, the user must wait at least t
WD_EEPROM before issuing the next byte. (Please
refer to Table 42.)
7.
Any memory location can be verified by using the Read instruction, which
returns the content at the selected address at serial output PE1(PDO/TXD).
8.
At the end of the programming session, RESET can be set high to commence
normal operation.
9.
Power-off sequence (if needed): Set XTAL1 to “0” (if a crystal is not used). Set
RESET to “1”. Turn V
CC power off.
Table 42 shows the actual delays used in this section.
Please note: The MISO pin is not high-Z during serial programming.
Data Polling for the EEPROM
When a new EEPROM byte has been written and is being programmed into the
EEPROM, reading the address location being programmed will first give the value P1
(please refer to Table 43) until the auto-erase is finished, and then the value P2.
At the time the device is ready for a new EEPROM byte, the programmed value will read
correctly. This is used to determine when the next byte can be written. This will not work
for the values P1 and P2, so when programming these values, the user will have to wait
for at least the prescribed time t
WD_EEPROM (please refer to Table 42) before programming
the next byte. As a chip-erased device contains $FF in all locations, programming of
addresses that are meant to contain $FF can be skipped. This does not apply if the
EEPROM is reprogrammed without chip erasing the device.
相關PDF資料 |
PDF描述 |
|---|---|
| ATMEGA128A-AUR | MCU AVR 128K FLASH 16MHZ 64TQFP |
| ATMEGA128L-8MJ | IC MCU AVR 128K 8MHZ LV 64-QFN |
| ATMEGA16-16MUR | MCU AVR 16KB FLASH 16MHZ 44QFN |
| ATMEGA164PA-AN | IC MCU AVR 16K FLASH 44TQFP |
| ATMEGA164PA-CUR | MCU AVR 16KB FLASH 20MHZ 49VFBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATMEGA103L | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 128K Bytes In-System Programmable Flash |
| ATMEGA103L-4AC | 功能描述:8位微控制器 -MCU TQFP-64 128K FLASH 3 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ATMEGA103L-4AI | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-Bit Microcontroller with 64K/128K Bytes In-System Programmable Flash |
| ATMEGA128 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 128K Bytes In-System Programmable Flash |
| ATMEGA128(L) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ATmega128(L) Preliminary Summary [Updated 9/03. 23 Pages] |
發布緊急采購，3分鐘左右您將得到回復。