參數資料
型號： ATMEGA103-6AI
廠商： Atmel
文件頁數： 110/141頁
文件大小： 0K
描述： IC MCU 128K 6MHZ A/D IT 64TQFP
產品培訓模塊： megaAVR Introduction
標準包裝： 90
系列： AVR® ATmega
核心處理器： AVR
芯體尺寸： 8-位
速度： 6MHz
連通性： SPI，UART/USART
外圍設備： POR，PWM，WDT
輸入/輸出數： 32
程序存儲器容量： 128KB（64K x 16）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 4K x 8
RAM 容量： 4K x 8
電壓 - 電源 (Vcc/Vdd)： 4 V ~ 5.5 V
數據轉換器： A/D 8x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 64-TQFP
包裝： 托盤
配用： ATSTK501-ND - ADAPTER KIT FOR 64PIN AVR MCU
70
ATmega103(L)
0945I–AVR–02/07
UART Control
UART I/O Data Register – UDR
The UDR Register is actually two physically separate registers sharing the same I/O
address. When writing to the register, the UART Transmit Data Register is written.
When reading from UDR, the UART Receive Data Register is read.
UART Status Register – USR
The USR Register is a read-only register providing information on the UART Status.
Bit 7 – RXC: UART Receive Complete
This bit is set (one) when a received character is transferred from the Receiver Shift
Register to UDR. The bit is set regardless of any detected framing errors. When the
RXCIE bit in UCR is set, the UART Receive Complete interrupt will be executed when
RXC is set (one). RXC is cleared by reading UDR. When interrupt-driven data reception
is used, the UART Receive Complete Interrupt routine must read UDR in order to clear
RXC, otherwise a new interrupt will occur once the interrupt routine terminates.
Bit 6 – TXC: UART Transmit Complete
This bit is set (one) when the entire character (including the stop bit) in the Transmit
Shift Register has been shifted out and no new data has been written to the UDR. This
flag is especially useful in half-duplex communications interfaces, where a transmitting
application must enter Receive mode and free the communications bus immediately
after completing the transmission.
When the TXCIE bit in UCR is set, setting of TXC causes the UART Transmit Complete
interrupt to be executed. TXC is cleared by hardware when executing the corresponding
interrupt handling vector. Alternatively, the TXC bit is cleared (zero) by writing a logical
“1” to the bit.
Bit 5 – UDRE: UART Data Register Empty
This bit is set (one) when a character written to UDR is transferred to the Transmit Shift
Register. Setting of this bit indicates that the Transmitter is ready to receive a new char-
acter for transmission.
When the UDRIE bit in UCR is set, the UART Transmit Complete interrupt to be exe-
cuted as long as UDRE is set. UDRE is cleared by writing UDR. When interrupt-driven
data transmittal is used, the UART Data Register Empty Interrupt routine must write
UDR in order to clear UDRE, otherwise a new interrupt will occur once the interrupt rou-
tine terminates.
UDRE is set (one) during reset to indicate that the Transmitter is ready.
Bit
7654
321
0
$0C ($2C)
MSB
LSB
UDR
Read/Write
R/W
Initial Value
0000
000
0
Bit
7654
321
0
$0B ($2B)
RXC
TXC
UDRE
FE
OR
–
USR
Read/Write
R
R/W
R
Initial Value
0010
000
0
相關PDF資料
PDF描述
ATMEGA128A-AUR MCU AVR 128K FLASH 16MHZ 64TQFP
ATMEGA128L-8MJ IC MCU AVR 128K 8MHZ LV 64-QFN
ATMEGA16-16MUR MCU AVR 16KB FLASH 16MHZ 44QFN
ATMEGA164PA-AN IC MCU AVR 16K FLASH 44TQFP
ATMEGA164PA-CUR MCU AVR 16KB FLASH 20MHZ 49VFBGA
相關代理商/技術參數
參數描述
ATMEGA103L 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 128K Bytes In-System Programmable Flash
ATMEGA103L-4AC 功能描述:8位微控制器 -MCU TQFP-64 128K FLASH 3 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATMEGA103L-4AI 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-Bit Microcontroller with 64K/128K Bytes In-System Programmable Flash
ATMEGA128 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 128K Bytes In-System Programmable Flash
ATMEGA128(L) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ATmega128(L) Preliminary Summary [Updated 9/03. 23 Pages]
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*