參數資料
型號： AK61584
廠商： Asahi Kasei Microsystems Co.,Ltd
元件分類： 圓形連接器
英文描述： Circular Connector; No. of Contacts:55; Series:MS27484; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:16; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:16-35 RoHS Compliant: No
中文描述： 雙低功耗的T1/E1線路接口
文件頁數： 35/38頁
文件大?。?/td> 364K
代理商： AK61584
ASAHI KASEI
[AK61584]
0185-E-00
98/04
-35-
CON01, CON11, CON21,
CON02. CON12, CON22 -Configuration Selection, Pins 58, 53, 51, 54, 52, 50.
(Hardware Mode)
Configures the transmitter (pulse shape, pulse width, pulse amplitude and driver impedance),
receiver (slicing level), and coder (HDB3 vs B8ZS)as shown in Table 1. The CONx1 pins
control channel 1. The CONx2 pins control channel 2. Both channels must operate at the
same rate (both T1 or both E1).
CS -Chip Select, Pin 64. (Host modes)
Pin most transition from high to low to read or write the serial port.
INT -Receive Alarm Interrupt, Pin 63. (Host mode)
An interrupt is generated when a status register changes state to flag the host processor.
INT is cleared by reading the status registers. The logic level for an active interrupt
alarm is controlled by pin IPOL. INT is an open drain output and should be tied to the
appropriate supply through a resistor.
IPOL -Interrupt Polarity, Pin 33. (Host mode)
IPOL controls INT polarity. Setting IPOL to logic 1 causes interrupts to be indicated by
INT equal high. Setting IPOL to logic 0 causes interrupts to be indicated by INT equal to
low.
LLOOP1, LLOOP2 -Local Loopback, Pin 62,61. (Hardware Mode)
Setting LLOOP to a logic 1 activates Local Loopback #1. TCLK and TPOS/TNEG (TDATA)
are still transmitted unless overridden by a TAOS request. Inputs on RTIP and RRING are ignored.
MODE -Mode Select, Pin 21.
Setting MODE to logic 1 puts the line interface in the host mode. In the host mode, a serial
interface is used to control the line interface and monitor its status.
Setting MODE to logic 0 puts the line interface in the hardware mode, where it is
configured and monitored using discrete pins. MODE defined the function of pins shown
across the top of the block diagram on the front page of the data sheet. Setting MODE to
AV+/2 volts will cause unpredictable results.
PD1, PD2 - Power Down, Pins 15, 34.
Setting PD1 or PD2 to logic 1 puts the channel 1 or channel 2 line interface, respectively,
in a low power, inactive state. Setting PD1 or PD2 to logic 0 returns the selected channel
to normal operation.
RESET -Reset, Pin 25.
Setting RESET to logic 1 resets the AK61584, clears the host-mode control registers, and
then sets LOS high.
RLOOP1,RLOOP2-Remote Loopback, Pins 63,33. (Hardware Mode)
Setting RLOOP to a logic 1 causes the recovered clock and data on both channels to be sent
through the driver back to the line. The recovered signal is also sent to RCLK and RPOS/RNEG.(RDATA)
相關PDF資料
PDF描述
AK6416A 16Kbit Serial CMOS EEPROM
AK6416AM 16Kbit Serial CMOS EEPROM
AK6416C 16Kbit Serial CMOS EEPROM
AK6416CH 16Kbit Serial CMOS EEPROM
AK6416CM 16Kbit Serial CMOS EEPROM
相關代理商/技術參數
參數描述
AK616-.5 功能描述:CABLE AUDIO CD-ROM 3-FOLD .5M RoHS:否 類別:電纜組件 >> 矩形 系列:- 標準包裝:1 系列:- 連接器類型:插頭至插頭 位置數:30 行數:2 間距 - 連接器:0.100"（2.54mm） 間距 - 線纜:0.050"（1.27mm） 長度:1.50'（457.20mm） 特點:電極標記 顏色:多色，帶狀 屏蔽:無屏蔽 使用:- 電纜端接:IDC 觸點表面涂層:金 觸點涂層厚度:30µin（0.76µm）
AK6161024D 制造商:ACCUTEK 制造商全稱:ACCUTEK MICROCIRCUIT CORPORATION 功能描述:65,536 x 32 Bit CMOS/BiCMOS Static Random Access Memory
AK6161024G 制造商:ACCUTEK 制造商全稱:ACCUTEK MICROCIRCUIT CORPORATION 功能描述:32,768 x 32 Bit CMOS/BiCMOS Static Random Access Memory
AK6161024S 制造商:ACCUTEK 制造商全稱:ACCUTEK MICROCIRCUIT CORPORATION 功能描述:65,536 x 32 Bit CMOS/BiCMOS Static Random Access Memory
AK6161024W 制造商:ACCUTEK 制造商全稱:ACCUTEK MICROCIRCUIT CORPORATION 功能描述:65,536 x 32 Bit CMOS/BiCMOS Static Random Access Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*