- 您現在的位置：買賣IC網 > PDF目錄385096 > AK61584 (Asahi Kasei Microsystems Co.,Ltd) Circular Connector; No. of Contacts:55; Series:MS27484; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:16; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:16-35 RoHS Compliant: No PDF資料下載
參數資料
| 型號： | AK61584 |
| 廠商： | Asahi Kasei Microsystems Co.,Ltd |
| 元件分類： | 圓形連接器 |
| 英文描述： | Circular Connector; No. of Contacts:55; Series:MS27484; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:16; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:16-35 RoHS Compliant: No |
| 中文描述： | 雙低功耗的T1/E1線路接口 |
| 文件頁數： | 16/38頁 |
| 文件大?。?/td> | 364K |
| 代理商： | AK61584 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
ASAHI KASEI
[AK61584]
0185-E-00
98/04
-16-
When the jitter attenuator is in the receive path, upon loss
of signal, the frequency of last recovered signal is
held over. When the jitter attenuator is not in the re-
ceive path, the last recovered frequency is not held over,
Rather, the output frequency will become the frequen-
cy of the reference clock.
Any time a channel is reset or powered down, (for
example by RESET, PD1, PD2, or power-on reset),
the loss of signal indicator on that channel is set high.
The loss of signal indicator remains high until data is
recovered by the receiver.
Receiver AIS Detection
The receiver detects AIS upon observation of
99.9% ones density for 5.3 ms. More specifically, the AIS
detection criteria is less than 9 zeros out of 8192 bits.
When AIS is detected, the AK61584 sets the control
register bits AIS and Latched-AIS, high. In the coder
mode, the receiver also sets output pin AIS high. The
end of the AIS condition occurs when
>
9 zeros are
detected out of 8192 bits. The AIS bits in the status
register operate the same as the LOS bits (see Ta-
ble5) upon detecting AIS. When a channel is powered
down, all indications are forced low.
JITTER ATTENUATOR
The jitter attenuator can be switched into either the receive
or transmit paths. Alternatively it can be removed from
both paths (thereby decreasing propagation delay).
Atten0x
Atten1x
Location of
Jitter Attenuator
Receiver
Transmitter
Neither
Reserved
0
0
1
1
0
1
0
1
Table 4. Jitter Attenuation Control
In hardware mode, the location of the attenuators is the
same for channel 1 and 2, and is controlled by pins
ATTEN0 and ATTEN1. See Table4. In host modes,
Figure 13. Typical Jitter Transfer Function
the location of the attenuators is programmable on a
per-channel basis, using bits ATTEN01
ATTEN11 for channel 1, and bits ATTEN02 and
ATTEN12 for channel 2. The control bits also conform
to Table 4.
and
A typical jitter attenuation curve is shown in Figure 13.
The attenuator consists of a 64-bit FIFO, a nar-
row-band monolithic PLL, and control logic. Signal
jitter is absorbed in the FIFO. The FIFO is designed to
neither overflow nor underflow. If overflow or under-
flow is imminent, the jitter transfer function is altered to
insure that no bit errors occur. Under this circumstance, jit-
ter gain may occur, and jitter should be attenuated exter-
nally in a frame buffer. The jitter attenuator will typi-
cally tolerate 43 UIs before the overflow/underflow
mechanism takes effect. Before the jitter attenuator has
had time to “l(fā)ock” to the average incoming frequency,
for example, after a chip reset, the attenuator will tolerate
a minimum of 22 UIs before the overflow/underflow
mechanism takes effect.
For T1/E1 line cards employed in high-speed mul-
tiplexers (e.g.,SONET and SDH), the jitter attenu-
ator is typically used in the transmit path. The attenuator
can be fed a gapped transmit clock, with gaps 22 UIs,
and transmit clock burst rate
<
8 MHz.
相關PDF資料 |
PDF描述 |
|---|---|
| AK6416A | 16Kbit Serial CMOS EEPROM |
| AK6416AM | 16Kbit Serial CMOS EEPROM |
| AK6416C | 16Kbit Serial CMOS EEPROM |
| AK6416CH | 16Kbit Serial CMOS EEPROM |
| AK6416CM | 16Kbit Serial CMOS EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AK616-.5 | 功能描述:CABLE AUDIO CD-ROM 3-FOLD .5M RoHS:否 類別:電纜組件 >> 矩形 系列:- 標準包裝:1 系列:- 連接器類型:插頭至插頭 位置數:30 行數:2 間距 - 連接器:0.100"（2.54mm） 間距 - 線纜:0.050"（1.27mm） 長度:1.50'（457.20mm） 特點:電極標記 顏色:多色，帶狀 屏蔽:無屏蔽 使用:- 電纜端接:IDC 觸點表面涂層:金 觸點涂層厚度:30µin（0.76µm） |
| AK6161024D | 制造商:ACCUTEK 制造商全稱:ACCUTEK MICROCIRCUIT CORPORATION 功能描述:65,536 x 32 Bit CMOS/BiCMOS Static Random Access Memory |
| AK6161024G | 制造商:ACCUTEK 制造商全稱:ACCUTEK MICROCIRCUIT CORPORATION 功能描述:32,768 x 32 Bit CMOS/BiCMOS Static Random Access Memory |
| AK6161024S | 制造商:ACCUTEK 制造商全稱:ACCUTEK MICROCIRCUIT CORPORATION 功能描述:65,536 x 32 Bit CMOS/BiCMOS Static Random Access Memory |
| AK6161024W | 制造商:ACCUTEK 制造商全稱:ACCUTEK MICROCIRCUIT CORPORATION 功能描述:65,536 x 32 Bit CMOS/BiCMOS Static Random Access Memory |
發布緊急采購，3分鐘左右您將得到回復。