- 您現在的位置：買賣IC網 > PDF目錄1900 > ADUC834BCPZ-REEL (Analog Devices Inc)IC MCU 62K FLASH ADC/DAC 56LFCSP PDF資料下載
參數資料
| 型號： | ADUC834BCPZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 44/80頁 |
| 文件大小： | 0K |
| 描述： | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| 標準包裝： | 2,500 |
| 系列： | MicroConverter® ADuC8xx |
| 核心處理器： | 8052 |
| 芯體尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 連通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外圍設備： | POR，PSM，PWM，溫度傳感器，WDT |
| 輸入/輸出數： | 34 |
| 程序存儲器容量： | 62KB（62K x 8） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 5.25 V |
| 數據轉換器： | A/D 3x16b，4x24b; D/A 1x12b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 56-VFQFN 裸露焊盤，CSP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
REV. A
ADuC834
–49–
Port 1
Port 1 is also an 8-bit port directly controlled via the P1 SFR.
The Port 1 pins are divided into two distinct pin groupings P1.0
to P1.1 and P1.2 to P1.7.
P1.0 and P1.1
P1.0 and P1.1 are bidirectional digital I/O pins with internal
pull-ups.
If P1.0 and P1.1 have 1s written to them via the P1 SFR, these
pins are pulled high by the internal pull-up resistors. In this state,
they can also be used as inputs. As input pins being externally
pulled low, they will source current because of the internal
pull-ups. With 0s written to them, both these pins will drive a
logic low output voltage (VOL) and will be capable of sinking
10 mA compared to the standard 1.6 mA sink capability on the
other port pins.
These pins also have various secondary functions described in
Table XXIV. The timer 2 alternate functions of P1.0 and P1.1
can only be activated if the corresponding bit latch in the P1
SFR contains a 1. Otherwise, the port pin is stuck at 0. In the
case of the PWM outputs at P1.0 and P1.1, the PWM outputs
will overwrite anything written to P1.0 or P1.1.
Table XXIV. P1.0 and P1.1 Alternate Pin Functions
Pin
Alternate Function
P1.0
T2 (Timer/Counter 2 External Input)
PWM0 (PWM0 output at this pin)
P1.1
T2EX (Timer/Counter 2 Capture/Reload Trigger)
PWM1 (PWM1 output at this pin)
Figure 37 shows a typical bit latch and I/O buffer for a P1.0 or
P1.1 port pin. No external memory access is required from
either of these pins although internal pull-ups are present.
READ
LATCH
INTERNAL
BUS
WRITE
TO LATCH
READ
PIN
D
CL
Q
LATCH
P1.x
PIN
ALTERNATE
OUTPUT FUNCTION
DVDD
INTERNAL
PULL-UP*
*SEE FIGURE 38
FOR DETAILS OF
INTERNAL PULL-UP
ALTERNATE
INPUT
FUNCTION
Figure 37. P1.0 and P1.1 Bit Latch and I/O Buffer
The internal pull-up consists of active circuitry as shown in
Figure 38. Whenever a P1.0 or P1.1 bit latch transitions from
low to high, Q1 in Figure 38 turns on for 2 oscillator periods to
quickly pull the pin to a logic high state. Once there, the weaker
Q3 turns on, thereby latching the pin to a logic high. If the pin
is momentarily pulled low externally, Q3 will turn off, but the
very weak Q2 will continue to source some current into the pin,
attempting to restore it to a logic high.
Q
FROM
PORT
LATCH
2 CLK
DELAY
Q1
DVDD
Q2
DVDD
Q3
DVDD
Px.x
PIN
Q4
Figure 38. Internal Pull-Up Configuration
8052 COMPATIBLE ON-CHIP PERIPHERALS
This section gives a brief overview of the various secondary
peripheral circuits that are also available to the user on-chip.
These remaining functions are mostly 8052 compatible (with a
few additional features) and are controlled via standard 8052
SFR bit definitions.
Parallel I/O
The ADuC834 uses four input/output ports to exchange data
with external devices. In addition to performing general-purpose
I/O, some ports are capable of external memory operations while
others are multiplexed with alternate functions for the peripheral
features on the device. In general, when a peripheral is enabled,
that pin may not be used as a general-purpose I/O pin.
Port 0
Port 0 is an 8-bit open-drain bidirectional I/O port that is directly
controlled via the Port 0 SFR. Port 0 is also the multiplexed low
order address and databus during accesses to external program
or data memory.
Figure 36 shows a typical bit latch and I/O buffer for a Port 0 port
pin. The bit latch (one bit in the port’s SFR) is represented as a
Type D flip-flop, which will clock in a value from the internal bus
in response to a “write to latch” signal from the CPU. The Q output
of the flip-flop is placed on the internal bus in response to a
“read latch” signal from the CPU. The level of the port pin itself
is placed on the internal bus in response to a “read pin” signal
from the CPU. Some instructions that read a port activate the
“read latch” signal, and others activate the “read pin” signal.
See the following Read-Modify-Write Instructions section for
more details.
CONTROL
READ
LATCH
INTERNAL
BUS
WRITE
TO LATCH
READ
PIN
D
CL
Q
LATCH
DVDD
ADDR/DATA
P0.x
PIN
Figure 36. Port 0 Bit Latch and I/O Buffer
As shown in Figure 36, the output drivers of Port 0 pins are
switchable to an internal ADDR and ADDR/DATA bus by an
internal CONTROL signal for use in external memory accesses.
During external memory accesses, the P0 SFR gets 1s written to
it (i.e., all of its bit latches become 1). When accessing external
memory, the CONTROL signal in Figure 36 goes high, enabling
push-pull operation of the output pin from the internal address
or databus (ADDR/DATA line). Therefore, no external pull-ups
are required on Port 0 in order for it to access external memory.
In general-purpose I/O port mode, Port 0 pins that have 1s
written to them via the Port 0 SFR will be configured as open-
drain and will therefore float. In this state, Port 0 pins can be
used as high impedance inputs. This is represented in Figure 36
by the NAND gate whose output remains high as long as the
CONTROL signal is low, thereby disabling the top FET. Exter-
nal pull-up resistors are therefore required when Port 0 pins are
used as general-purpose outputs. Port 0 pins with 0s written to
them will drive a logic low output voltage (VOL) and will be
capable of sinking 1.6 mA.
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC836BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC843BSZ62-5 | IC ADC 12BIT W/FLASH MCU 52-MQFP |
| ADUC845BCPZ62-5 | IC FLASH MCU W/24BIT ADC 56-CSP |
| ADUC847BCPZ62-5 | IC MCU FLASH W/24BIT ADC 56-CSP |
| ADV202BBCZ-135 | IC CODEC VIDEO 135MHZ 144CSPBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC834BS | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 12.58MHZ 3.3/5V 52MQFP - Bulk 制造商:Analog Devices 功能描述:8BIT MCU +24/16BIT ADC SMD MQFP52 |
| ADUC834BSZ | 功能描述:IC ADC DUAL16/24BIT W/MCU 52MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| ADUC836 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU |
| ADUC836_02 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62 kB Flash MCU |
| ADUC836BCP | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。