- 您現在的位置：買賣IC網 > PDF目錄1900 > ADUC834BCPZ-REEL (Analog Devices Inc)IC MCU 62K FLASH ADC/DAC 56LFCSP PDF資料下載
參數資料
| 型號： | ADUC834BCPZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 24/80頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| 標準包裝： | 2,500 |
| 系列： | MicroConverter® ADuC8xx |
| 核心處理器： | 8052 |
| 芯體尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 連通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外圍設備： | POR，PSM，PWM，溫度傳感器，WDT |
| 輸入/輸出數： | 34 |
| 程序存儲器容量： | 62KB（62K x 8） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 5.25 V |
| 數據轉換器： | A/D 3x16b，4x24b; D/A 1x12b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 56-VFQFN 裸露焊盤，CSP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
REV. A
–30–
ADuC834
Flash/EE Program Memory
The ADuC834 contains a 64 Kbyte array of Flash/EE program
memory. The lower 62 Kbytes of this program memory is avail-
able to the user, and can be used for program storage or indeed
as additional NV data memory.
The upper 2 Kbytes of this Flash/EE program memory array
contain permanently embedded firmware, allowing in circuit serial
download, serial debug and nonintrusive single pin emulation.
These 2 Kbytes of embedded firmware also contain a power-on
configuration routine that downloads factory calibrated coeffi-
cients to the various calibrated peripherals (ADC, temperature
sensor, current sources, bandgap references and so on).
This 2 Kbyte embedded firmware is hidden from user code.
Attempts to read this space will read 0s, i.e., the embedded firmware
appears as NOP instructions to user code.
In normal operating mode (power up default) the 62 Kbytes of
user Flash/EE program memory appear as a single block. This
block is used to store the user code as shown in Figure 17.
FFFFH
0000H
F800H
F7FFH
USER PROGRAM MEMORY
62 KBYTES OF FLASH/EE PROGRAM MEMORY IS
AVAILABLE TO THE USER. ALL OF THIS SPACE CAN
BE PROGRAMMED FROM THE PERMANENTLY
EMBEDDED DOWNLOAD/DEBUG KERNEL OR IN
PARALLEL PROGRAMMING MODE.
EMBEDDED DOWNLOAD/DEBUG KERNEL
PERMANENTLY EMBEDDED FIRMWARE ALLOWS CODE
TO BE DOWNLOADED TO ANY OF THE 62 KBYTES OF
ON-CHIP PROGRAM MEMORY. THE KERNEL PROGRAM
APPEARS AS ‘NOP’ INSTRUCTIONS TO USER CODE.
62 KBYTE
2 KBYTE
Figure 17. Flash/EE Program Memory Map in
Normal Mode
In Normal Mode, the 62 Kbytes of Flash/EE program memory
can be programmed programmed in two ways, namely:
(1) Serial Downloading (In-Circuit Programming)
The ADuC834 facilitates code download via the standard UART
serial port. The ADuC834 will enter Serial Download mode
after a reset or power cycle if the
PSEN pin is pulled low through
an external 1 k
resistor. Once in serial download mode, the
hidden embedded download kernel will execute. This allows the
user to download code to the full 62 Kbytes of Flash/EE program
memory while the device is in circuit in its target application
hardware.
A PC serial download executable is provided as part of the
ADuC834 QuickStart development system. Appliction Note
uC004 fully describes the serial download protocol that is used
by the embedded download kernel. This Appliction Note is
available at www.analog.com/microconverter.
(2) Parallel Programming
The parallel programming mode is fully compatible with conven-
tional third party Flash or EEPROM device programmers. A block
diagram of the external pin configuration required to support parallel
programming is shown in Figure 18. In this mode, Ports 0, and 2
operate as the external address bus interface, P3 operates as the
external data bus interface and P1.0 operates as the Write Enable
strobe. Port 1.1, P1.2, P1.3, and P1.4 are used as a general
configuration port that configures the device for various program
and erase operations during parallel programming.
Table XIII. Flash/EE Memory Parallel Programming Modes
Port 1 Pins
P1.4
P1.3
P1.2
P1.1
Programming Mode
0000
Erase Flash/EE Program,
Data, and Security Modes
1001
Read Device Signature/ID
1010
Program Code Byte
0010
Program Data Byte
1011
Read Code Byte
0011
Read Data Byte
1100
Program Security Modes
1101
Read/Verify Security Modes
All other codes
Redundant
VDD
GND
P1.1 -> P1.4
PSEN
RESET
P3
P0
P2
ADuC834
5V
PROGRAM MODE
(SEE TABLE XIII)
GND
PROGRAM
DATA
(D0–D7)
PROGRAM
ADDRESS
(A0–A13)
(P2.0 = A0)
(P1.7 = A13)
COMMAND
ENABLE
P1.0
EA
ENTRY
SEQUENCE
VDD
GND
P1.5 -> P1.7
TIMING
Figure 18. Flash/EE Memory Parallel Programming
User Download Mode (ULOAD)
In Figure 17 we can see that it was possible to use the 62 Kbytes
of Flash/EE program memory available to the user as one single
block of memory. In this mode all of the Flash/EE memory is
read only to user code.
However, the Flash/EE program memory can also be written to
during runtime simply by entering ULOAD mode. In ULOAD
mode, the lower 56 Kbytes of program memory can be erased
and reprogrammed by user software as shown in Figure 19.
ULOAD mode can be used to upgrade your code in the field via
any user defined download protocol. Configuring the SPI port on
the ADuC834 as a slave, it is possible to completely reprogram
the 56 Kbytes of Flash/EE program memory in only 5 seconds.
See Application Note uC007.
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC836BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC843BSZ62-5 | IC ADC 12BIT W/FLASH MCU 52-MQFP |
| ADUC845BCPZ62-5 | IC FLASH MCU W/24BIT ADC 56-CSP |
| ADUC847BCPZ62-5 | IC MCU FLASH W/24BIT ADC 56-CSP |
| ADV202BBCZ-135 | IC CODEC VIDEO 135MHZ 144CSPBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC834BS | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 12.58MHZ 3.3/5V 52MQFP - Bulk 制造商:Analog Devices 功能描述:8BIT MCU +24/16BIT ADC SMD MQFP52 |
| ADUC834BSZ | 功能描述:IC ADC DUAL16/24BIT W/MCU 52MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| ADUC836 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU |
| ADUC836_02 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62 kB Flash MCU |
| ADUC836BCP | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。