- 您現在的位置：買賣IC網 > PDF目錄1900 > ADUC832BSZ-REEL (Analog Devices Inc)IC MCU 62K FLASH ADC/DAC 52MQFP PDF資料下載
參數資料
| 型號： | ADUC832BSZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 86/92頁 |
| 文件大小： | 0K |
| 描述： | IC MCU 62K FLASH ADC/DAC 52MQFP |
| 標準包裝： | 800 |
| 系列： | MicroConverter® ADuC8xx |
| 核心處理器： | 8052 |
| 芯體尺寸： | 8-位 |
| 速度： | 16MHz |
| 連通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外圍設備： | PSM，溫度傳感器，WDT |
| 輸入/輸出數： | 34 |
| 程序存儲器容量： | 62KB（62K x 8） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 數據轉換器： | A/D 8x12b，D/A 2x12b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | 52-QFP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁當前第86頁第87頁第88頁第89頁第90頁第91頁第92頁
Data Sheet
ADuC832
Rev. B | Page 87 of 92
OTHER HARDWARE CONSIDERATIONS
To facilitate in-circuit programming, plus in-circuit debug and
emulation options, implement some simple connection points
in the hardware that allow easy access to download, debug, and
emulation modes.
IN-CIRCUIT SERIAL DOWNLOAD ACCESS
Nearly all ADuC832 designs can take advantage of the in-circuit
reprogrammability of the chip. This is accomplished by a
connection to the ADuC832 UART, which requires an external
RS-232 chip for level translation if downloading code from a
PC. Basic configuration of an RS-232 connection is illustrated
in Figure 94 with a simple ADM202-based circuit. To avoid
designing an RS-232 chip onto a board, refer to the uC006
Technical Note, A 4-Wire UART-to-PC Interface, available at
www.analog.com, for a simple (and zero-cost-per-board)
method of gaining in-circuit serial download access to the
ADuC832.
In addition to the basic UART connections, users also need a way
to trigger the chip into download mode. This is accomplished via a
1 kΩ pull-down resistor that can be jumpered onto the PSEN
pin, as shown in Figure 94. To put the ADuC832 into download
mode, connect this jumper and power-cycle the device (or
manually reset the device, if a manual reset button is available)
so that it can receive a new program serially. With the jumper
removed, the device comes up in normal mode (and runs the
program) whenever power is cycled or RESET is toggled.
Note that PSEN is normally an output (as described in the
External Memory Interface section) and is sampled as an input
only on the falling edge of RESET (that is, at power-up or upon
an external manual reset). Note also that if any external circuitry
unintentionally pulls PSEN low during power-up or reset events, it
may cause the chip to enter download mode and therefore fail
to begin user code execution as it should. To prevent this, ensure
that no external signals are capable of pulling the PSEN pin low,
except for the external PSEN jumper itself.
EMBEDDED SERIAL PORT DEBUGGER
From a hardware perspective, entry into serial port debug mode
is identical to the serial download entry sequence described in
the In-Circuit Serial Download Access section. In fact, both
serial download and serial port debug modes can be thought of
as essentially one mode of operation used in two different ways.
Note that the serial port debugger is fully contained on the
ADuC832 device (unlike ROM monitor type debuggers) and
therefore no external memory is needed to enable in-system
debug sessions.
SINGLE-PIN EMULATION MODE
Also built into the ADuC832 is a dedicated controller for single-pin
in-circuit emulation (ICE) using standard production ADuC832
devices. In this mode, emulation access is gained by connection
to a single pin, the EA pin. Normally, this pin is hardwired
either high or low to select execution from internal or external
program memory space. To enable single-pin emulation mode,
however, users need to pull the EA pin high through a 1 kΩ
resistor, as shown in Figure 94. The emulator then connects to
the 2-pin header, also shown in Figure 94. To be compatible with
the standard connector that comes with the single-pin emulator,
use a 2-pin 0.1 inch pitch friction lock header from Molex such as
Part Number 22-27-2021. Be sure to observe the polarity of this
header. As represented in Figure 94, when the friction lock tab is
located on the right, the ground pin should be the lower of the
two pins (when viewed from the top).
TYPICAL SYSTEM CONFIGURATION
A typical ADuC832 configuration is shown in Figure 94. It
summarizes some of the hardware considerations discussed in
the Single-Pin Emulation Mode section.
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC834BCPZ-REEL | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC836BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC843BSZ62-5 | IC ADC 12BIT W/FLASH MCU 52-MQFP |
| ADUC845BCPZ62-5 | IC FLASH MCU W/24BIT ADC 56-CSP |
| ADUC847BCPZ62-5 | IC MCU FLASH W/24BIT ADC 56-CSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC832QS-U1 | 制造商:Analog Devices 功能描述:EVAL KIT - Bulk |
| ADUC834 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit/24-Bit ADCs with Embedded 62 kB Flash MCU |
| ADUC834_02 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit/24-Bit ADCs with Embedded 62 kB Flash MCU |
| ADUC834BCP | 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 12.58MHZ 3.3/5V 56LFCSP - Bulk 制造商:Analog Devices 功能描述: |
| ADUC834BCPZ | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587 |
發布緊急采購，3分鐘左右您將得到回復。