- 您現在的位置：買賣IC網 > PDF目錄8959 > AD9146BCPZ (Analog Devices Inc)IC DAC 16BIT SRL DUAL 48LFCSP PDF資料下載
參數資料
| 型號： | AD9146BCPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 43/56頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 16BIT SRL DUAL 48LFCSP |
| 標準包裝： | 1 |
| 系列： | TxDAC+® |
| 設置時間： | 20ns |
| 位數： | 16 |
| 數據接口： | 串行 |
| 轉換器數目： | 2 |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-WFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 48-LFCSP-WQ（7x7） |
| 包裝： | 托盤 |
| 輸出數目和類型： | 2 電流，單極 |
| 采樣率（每秒）： | 1.23G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
AD9146
Data Sheet
Rev. A | Page 48 of 56
When these conditions are met, the outputs of the DACs are
updated within one DAC clock cycle of each other. The timing
requirements of the input signals are shown in Figure 67.
DACCLKP(1)/
DACCLKN(1)
DACCLKP(2)/
DACCLKN(2)
REFCLKP(2)/
REFCLKN(2)
DCIP(2)/
DCIN(2)
FRAMEP(2)/
FRAMEN(2)
tSKEW
tSUSYNC
tHSYNC
09691-
073
Figure 67. FIFO Rate Synchronization Signal Timing Requirements,
2× Interpolation
Figure 67 shows the synchronization signal timing with 2×
interpolation; therefore, fDCI = × fCLK. The REFCLK input is
shown to be equal to the FIFO rate. The maximum frequency at
which the device can be resynchronized in FIFO rate mode can
be expressed as
fSYNC_I = fDATA/(8 × 2N)
where N is any non-negative integer.
ADDITIONAL SYNCHRONIZATION FEATURES
Table 25 shows the required timing between the DACCLK and the
synchronization clock when synchronization is used. This timing
restriction applies to both data rate mode and FIFO rate mode.
Table 25. Synchronization Setup and Hold Times
Parameter
Min
Max
Unit
tSKEW
tDACCLK/2
+tDACCLK/2
ps
tSUSYNC
100
ps
tHSYNC
330
ps
One-Time Synchronization
When implementing the full multichip synchronization feature
(with the REFCLK and FRAME signals aligned within one DACCLK
cycle), the user may experience difficulty meeting the DACCLK to
synchronization clock timing. In this case, a one-time synchroni-
zation method can be used. Before implementing the one-time
synchronization, make sure that the synchronization signal is
locked by checking both the sync signal locked and the sync signal
lost flags (Bit 4 and Bit 5 in Register 0x06). It is also important
that synchronization not be enabled before stable REFCLK signals
are present from the FPGA or ASIC. For more information and
a detailed flowchart of the one-time synchronization feature, see
the AN-1093 Application Note, “Synchronization of Multiple
AD9122 TxDAC+ Converters.”
Sync Status Bits
When the sync locked bit (Register 0x12, Bit 6) is set, it indicates
that the synchronization logic has reached alignment. This align-
ment is determined when the clock generation state machine
phase is constant.
Alignment takes from (11 + averaging) × 64 to (11 + averaging) ×
128 DACCLK cycles. The sync locked bit can also trigger an IRQ,
as described in the Interrupt Request Operation section.
When the sync lost bit (Register 0x12, Bit 7) is set, it indicates
that a previously synchronized device has lost alignment. This
bit is latched and remains set until cleared by overwriting the
register. This bit can also trigger an IRQ, as described in the
Interrupt Request Operation section.
The sync phase readback bits (Register 0x13, Bits[7:0]) report
the current clock phase in a 6.2 format. Bits[7:2] report which
of the 64 states (0 to 63) the clock is currently in. When averaging
is enabled, Bits[1:0] provide state accuracy (for 0, , , ).
The lower two bits give an indication of the timing margin issues
that may exist. If the synchronization sampling is error free, the
fractional clock state should be 00.
Timing Optimization
The REFCLK signal is sampled by a version of the DACCLK.
If sampling errors are detected, the opposite sampling edge can
be selected to improve the sampling point. The sampling edge
can be selected by setting Register 0x10, Bit 3 (1 = rising and
0 = falling).
The synchronization logic resynchronizes when a phase change
between the REFCLK signal and the state of the clock generation
state machine exceeds a threshold. To mitigate the effects of
jitter and prevent erroneous resynchronizations, the relative
phase can be averaged. The amount of averaging is set by the
sync averaging bits (Register 0x10, Bits[2:0]) and can be set
from 1 to 128. The higher the number of averages, the more
slowly the device recognizes and resynchronizes to a legitimate
phase correction. Generally, the averaging should be made as large
as possible while still meeting the allotted resynchronization
time interval. Note that, if the average synchronization sampling
result is in approximately the middle of the probability curve,
the synchronization engine can be unstable, resulting in
corrupted output.
The value of the Sync Phase Request[5:0] bits (Register 0x11,
Bits[5:0]) is the state to which the clock generation state machine
resets upon initialization. By varying this value, the timing of the
internal clocks, with respect to the REFCLK signal, can be adjusted.
Every increment of the Sync Phase Request[5:0] value advances the
internal clocks by one DACCLK cycle. This offset can be used for
two purposes: to skew the outputs of two synchronized DAC
outputs in increments of the DACCLK cycle, and to change the
relative timing between the DAC output and the sync input
(REFCLK). This may allow for a more optimal placement of the
DCI sampling point in data rate synchronization mode.
相關PDF資料 |
PDF描述 |
|---|---|
| GTC02R-36-5P | CONN RCPT 4POS BOX MNT W/PINS |
| VE-2TY-MX-F2 | CONVERTER MOD DC/DC 3.3V 49.5W |
| MS27508E24B4PC | CONN RCPT 56POS BOX MNT W/PINS |
| VE-2TY-MW-F2 | CONVERTER MOD DC/DC 3.3V 66W |
| MS27508E24B4PB | CONN RCPT 56POS BOX MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9146BCPZRL | 功能描述:IC DAC 16BIT SRL DUAL 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD9146-EBZ | 制造商:Analog Devices 功能描述:16 BIT DUAL SIGNAL PROC DAC EB - Boxed Product (Development Kits) |
| AD9146-M5375-EBZ | 功能描述:BOARD EVAL FOR AD9146 DAC RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9148 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad 16-Bit,1 GSPS, TxDAC+ Digital-to-Analog Converter |
| AD9148ARUZ | 制造商:Analog Devices 功能描述:- Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。