參數資料
型號： AD9146BCPZ
廠商： Analog Devices Inc
文件頁數： 32/56頁
文件大小： 0K
描述： IC DAC 16BIT SRL DUAL 48LFCSP
標準包裝： 1
系列： TxDAC+®
設置時間： 20ns
位數： 16
數據接口： 串行
轉換器數目： 2
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-WFQFN 裸露焊盤，CSP
供應商設備封裝： 48-LFCSP-WQ（7x7）
包裝： 托盤
輸出數目和類型： 2 電流，單極
采樣率（每秒）： 1.23G
AD9146
Data Sheet
Rev. A | Page 38 of 56
PLL SETTINGS
Three settings for the PLL circuitry should be programmed to
their nominal values. The PLL values shown in Table 21 are the
recommended settings for these parameters.
Table 21. PLL Settings
PLL Control Register
Register
Address
Bits
Optimal
Setting
PLL Loop Bandwidth[1:0]
0x0C
[7:6]
11
PLL Charge Pump Current[4:0]
0x0C
[4:0]
10001
PLL Cross-Control Enable
0x0D
4
1
CONFIGURING THE VCO TUNING BAND
The PLL VCO has a valid operating range from approximately
1.0 GHz to 2.1 GHz covered in 63 overlapping frequency bands.
For any desired VCO output frequency, there may be several
valid PLL band select values. The frequency bands of a typical
device are shown in Figure 49. Device-to-device variations and
operating temperature affect the actual band frequency range.
Therefore, it is required that the optimal PLL band select value
be determined for each individual device.
0
4
8
12
16
20
24
28
32
36
40
44
48
52
56
60
1000
2200
2000
1800
1600
1400
1200
P
L
BAND
VCO FREQUENCY (MHz)
09691-
054
Figure 49. PLL Lock Range over Temperature for a Typical Device
Automatic VCO Band Select
The device has an automatic VCO band select feature on chip.
Using the automatic VCO band select feature is a simple and
reliable method of configuring the VCO frequency band. This
feature is enabled by starting the PLL in manual mode, then
placing the PLL in auto band select mode. This is done by
setting Register 0x0A to a value of 0xCF, then to a value of
0xA0. When these values are written, the device executes an
automated routine that determines the optimal VCO band
setting for the device. The setting selected by the device ensures
that the PLL remains locked over the full 40°C to +85°C
operating temperature range of the device without further
adjustment. (The PLL remains locked over the full temperature
range even if the temperature during initialization is at one of
the temperature extremes.)
Manual VCO Band Select
The device also has a manual band select mode (PLL manual
enable, Register 0x0A, Bit 6 = 1) that allows the user to select
the VCO tuning band. In manual mode, the VCO band is set
directly with the value written to the manual VCO band bits
(Register 0x0A, Bits[5:0]). To properly select the VCO band,
follow these steps:
1. Put the device in manual band select mode by setting
Register 0x0A, Bit 6 = 1.
2. Sweep the VCO band over a range of bands that results in
the PLL being locked.
3. For each band, verify that the PLL is locked and read the
PLL using the VCO control voltage bits (Register 0x0E,
Bits[3:0]).
4. Select the band that results in the control voltage being
closest to the center of the range, that is, 1001 or 1000 (see
Table 22). The resulting VCO band should be the optimal
setting for the device. Write this value to the manual VCO
band bits (Register 0x0A, Bits[5:0]).
5. If desired, an indication of where the VCO is within the
operating frequency band can be determined by querying
the VCO control voltage. Table 22 shows how to interpret
the PLL VCO control voltage value (Register 0x0E, Bits[3:0]).
Table 22. VCO Control Voltage Range Indications
VCO Control Voltage
(Register 0x0E, Bits[3:0])
Indication
1111
Move to higher VCO band
1110
1101
VCO is operating in the higher end
of the frequency band
1100
1011
1010
1001
VCO is operating within an optimal
region of the frequency band
1000
0111
0110
0101
VCO is operating in the lower end
of the frequency band
0100
0011
0010
0001
Move to lower VCO band
0000
相關PDF資料
PDF描述
GTC02R-36-5P CONN RCPT 4POS BOX MNT W/PINS
VE-2TY-MX-F2 CONVERTER MOD DC/DC 3.3V 49.5W
MS27508E24B4PC CONN RCPT 56POS BOX MNT W/PINS
VE-2TY-MW-F2 CONVERTER MOD DC/DC 3.3V 66W
MS27508E24B4PB CONN RCPT 56POS BOX MNT W/PINS
相關代理商/技術參數
參數描述
AD9146BCPZRL 功能描述:IC DAC 16BIT SRL DUAL 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:*
AD9146-EBZ 制造商:Analog Devices 功能描述:16 BIT DUAL SIGNAL PROC DAC EB - Boxed Product (Development Kits)
AD9146-M5375-EBZ 功能描述:BOARD EVAL FOR AD9146 DAC RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
AD9148 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad 16-Bit,1 GSPS, TxDAC+ Digital-to-Analog Converter
AD9148ARUZ 制造商:Analog Devices 功能描述:- Rail/Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*