參數資料
型號： 73S1209F-EB
廠商： Maxim Integrated Products
文件頁數： 121/123頁
文件大小： 0K
描述： BOARD EVAL 73S1209F DOC/CD CABLE
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1
主要目的： *
嵌入式： *
已用 IC / 零件： *
主要屬性： *
次要屬性： *
已供物品： 板，線纜，CD，電源
DS_1209F_004
73S1209F Data Sheet
Rev. 1.2
97
CRC MS Value Registers (CRCMsB): 0xFE14
0xFF, (CRCLsB): 0xFE15
0xFF
Table 94: The CRCMsB Register
MSB
LSB
CRC.15
CRC.14
CRC.13
CRC.12
CRC.11
CRC.10
CRC.9
CRC.8
Table 95: The CRCLsB Register
MSB
LSB
CRC.7
CRC.6
CRC.5
CRC.4
CRC.3
CRC.2
CRC.1
CRC.0
The 16-bit CRC value forms the TX CRC word in TX mode (write value) and the RX CRC in RX mode
(read value). The initial value of CRC to be used when generating a CRC to be transmitted at the end of
a message (after the last TX byte is sent) when enabled in T=1 mode. Should be reloaded at the
beginning of every message to be transmitted. When using CRC, the both CRC registers should be
initialized to FF. When using LRC the CRCLsB Value register should be loaded to 00. When receiving a
message, the firmware should load this with the initial value and then read this register to get the final
value at the end of the message. These registers need to be reloaded for each new message to be
received. When in LRC mode, bits (7:0) are used and bits (15:8) are undefined. During LRC/CRC
checking and generation, this register is updated with the current value and can be read to aid in
debugging. This information will be transmitted to the smart card using the timing specified by the Guard
Time register. When checking CRC/LRC on an incoming message (CRC/LRC is checked against the
data and CRC/LRC), the firmware reads the final value after the message has been received and
determines if an error occurred (= 0x1D0F (CRC_ no error, else error; = 0 (LRC) no error, else error).
When a message is received, the CRC/LRC is stored in the FIFO. The polynomial used to generate and
check CRC is x
16 + x12+ x5 +1. When in indirect convention, the CRC is generated prior to the conversion
into indirect convention. When in indirect convention, the CRC is checked after the conversion out of
indirect convention. For a given message, the CRC generated (and readable from this register) will be
the same whether indirect or direct convention is used to transmit the data to the smart card. The
CRCLsB / CRCMsB registers will be updated with CRC/LRC whenever bits are being received or
transmitted from/to the smart card (even if CRCEN is not set and in mode T1). They are available to the
firmware to use if desired.
相關PDF資料
PDF描述
EBC25DTAS CONN EDGECARD 50POS R/A .100 SLD
DS8005-KIT# EVALUATION KIT FOR DS8005
UVR1A153MHD CAP ALUM 15000UF 10V 20% RADIAL
NR3012T150M INDUCTOR 15UH 20% SMD
PLE0E102MDO1 CAP ALUM 1000UF 2.5V 20% RADIAL
相關代理商/技術參數
參數描述
73S1209F-IM44 DK 制造商:Maxim Integrated Products 功能描述:Development Boards & Kits - 8051 73S1209F Dev Kit Eval Bd Ice Cable Cd
73S1209F-IM44 EB 制造商:Maxim Integrated Products 功能描述:Development Boards & Kits - 8051 73S1209F Eval Brd Eval Bd Doc Cd Cable
73S1209F-IM68 DK 制造商:Maxim Integrated Products 功能描述:Development Boards & Kits - 8051 73S1209F Dev Kit Eval Bd Ice Cable Cd
73S1209F-IM68 EB 制造商:Maxim Integrated Products 功能描述:Development Boards & Kits - 8051 73S1209F Eval Brd Doc Cd Cable
73S1210F 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Self-Contained Smart Card Reader with PINpad and Power Management
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*