- 您現在的位置：買賣IC網 > PDF目錄16263 > 73S1209F-EB (Maxim Integrated Products)BOARD EVAL 73S1209F DOC/CD CABLE PDF資料下載
參數資料
| 型號： | 73S1209F-EB |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 115/123頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL 73S1209F DOC/CD CABLE |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 主要目的： | * |
| 嵌入式： | * |
| 已用 IC / 零件： | * |
| 主要屬性： | * |
| 次要屬性： | * |
| 已供物品： | 板，線纜，CD，電源 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁當前第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁
DS_1209F_004
73S1209F Data Sheet
Rev. 1.2
91
Protocol Mode Register (SPrtcol): 0xFE0D
0x03
This register determines the protocol to be use when communicating with the selected smart card. This
register should be updated as required when switching between smart card interfaces.
Table 86: The SPrtcol Register
MSB
LSB
SCISYN
MOD9/8B SCESYN
0
TMODE
CRCEN
CRCMS RCVATR
Bit
Symbol
Function
SPrtcol.7
SCISYN
Smart Card Internal Synchronous mode – Configures internal smart card
interface for synchronous mode. This mode routes the internal interface
buffers for RST, IO, C4, C8 to SCCtl register bits for direct firmware control.
CLK is generated by the ETU counter.
SPrtcol.6
MOD9/8B
Synchronous 8/9 bit mode select – For sync mode, in protocols with 9-bit
words, set this bit. The first eight bits read go into the RX FIFO and the
ninth bit read will be stored in the IO (or SIO) data bit of the SRXCtl
register.
SPrtcol.5
SCESYN
Smart Card External Synchronous mode – Configures External Smart Card
interface for synchronous mode. This mode routes the external smart card
interface buffers for SIO to SCECtl register bits for direct firmware control.
SCLK is generated by the ETU counter.
SPrtcol.4
0
Reserved bit, must always be set to 0.
SPrtcol.3
TMODE
Protocol mode select – 0: T=0, 1: T=1. Determines which smart card
protocol is to be used during message processing.
SPrtcol.2
CRCEN
CRC Enable – 1 = Enabled, 0 = Disabled. Enables the
checking/generation of CRC/LRC while in T=1 mode. Has no effect in T=0
mode. If enabled and a message is being transmitted to the smart card,
the CRC/LRC will be inserted into the message stream after the last TX
byte is transmitted to the smart card. If enabled, CRC/LRC will be checked
on incoming messages and the value made available to the firmware via
the CRC LS/MS registers.
SPrtcol.1
CRCMS
CRC Mode Select - 1 = CRC, 0 = LRC. Determines type of checking
algorithm to be used.
SPrtcol.0
RCVATR
Receive ATR – 1 = Enable ATR timeout, 0 = Disable ATR timeout. Set by
firmware after the smart card has been turned on and the hardware is
expecting ATR.
相關PDF資料 |
PDF描述 |
|---|---|
| EBC25DTAS | CONN EDGECARD 50POS R/A .100 SLD |
| DS8005-KIT# | EVALUATION KIT FOR DS8005 |
| UVR1A153MHD | CAP ALUM 15000UF 10V 20% RADIAL |
| NR3012T150M | INDUCTOR 15UH 20% SMD |
| PLE0E102MDO1 | CAP ALUM 1000UF 2.5V 20% RADIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S1209F-IM44 DK | 制造商:Maxim Integrated Products 功能描述:Development Boards & Kits - 8051 73S1209F Dev Kit Eval Bd Ice Cable Cd |
| 73S1209F-IM44 EB | 制造商:Maxim Integrated Products 功能描述:Development Boards & Kits - 8051 73S1209F Eval Brd Eval Bd Doc Cd Cable |
| 73S1209F-IM68 DK | 制造商:Maxim Integrated Products 功能描述:Development Boards & Kits - 8051 73S1209F Dev Kit Eval Bd Ice Cable Cd |
| 73S1209F-IM68 EB | 制造商:Maxim Integrated Products 功能描述:Development Boards & Kits - 8051 73S1209F Eval Brd Doc Cd Cable |
| 73S1210F | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Self-Contained Smart Card Reader with PINpad and Power Management |
發布緊急采購，3分鐘左右您將得到回復。