- 您現在的位置：買賣IC網 > PDF目錄376463 > XRT83SL30 (Exar Corporation) SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR PDF資料下載
參數資料
| 型號： | XRT83SL30 |
| 廠商： | Exar Corporation |
| 英文描述： | SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| 中文描述： | 單通道的T1/E1/J1上海收發器時鐘恢復和抖動衰減器 |
| 文件頁數： | 7/76頁 |
| 文件大?。?/td> | 376K |
| 代理商： | XRT83SL30 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
á
XRT83SL30
SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
PRELIMINARY
REV. P1.0.4
4
PIN DESCRIPTIONS BY FUNCTION
SERIAL INTERFACE
S
IGNAL
N
AME
P
IN
#
T
YPE
D
ESCRIPTION
HW/HOST
20
I
Mode Control Input
This pin is used for selecting Hardware or
Host Mode
to control the device.
Leave this pin unconnected or tie “High” to select
Hardware Mode
.
For
Host Mode
, this pin must be tied “Low”.
N
OTE
:
Internally pulled “High” with a 50k
resistor.
SDI
EQC4
21
I
Serial Data Input
In
Host Mode
, this pin is the data input for the Serial Interface.
Equalizer Control Input 4
Hardware Mode
, See “Control function” on page 13.
SDO
EQC3
22
O
I
Serial Data Output
In
Host Mode
, this pin is the output “Read” data for the serial interface.
Equalizer Control Input 3
Hardware Mode
,
See “Control function” on page 13.
SCLK
EQC2
23
I
Serial Interface Clock Input
In
Host Mode
, this clock signal is used to control data “Read” or “Write”
operation for the Serial Interface. Maximum clock frequency is 20MHz.
Equalizer Control Input 2
Hardware Mode
, See “Control function” on page 13.
CS
EQC1
24
I
Chip Select Input
In
Host Mode
, tie this pin “Low” to enable communication with the device via
the Serial Interface.
Equalizer Control Input 1
Hardware Mode
, See “Control function” on page 13.
INT
EQC0
25
O
I
Interrupt Output (active "Low")
In
Host Mode
, this pin goes “Low” to indicate an alarm condition has
occurred within the device. Interrupt generation can be globally disabled by
setting the GIE bit to “0” in the command control register.
Equalizer Control Input 0
Hardware Mode
, See “Control function” on page 13.
N
OTE
:
This pin is an open drain output and requires an external 10k
pull-up
resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT83SL30IV | SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83VSH28 | 8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH28IB | 8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH314 | 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH314IB | 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83SL30ES | 功能描述:外圍驅動器與原件 - PCI 1 CHT1/E1 LIUSH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83SL30IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83SL30IV-F | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT83SL30IVTR-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83SL314 | 制造商:EXAR 制造商全稱:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
發布緊急采購，3分鐘左右您將得到回復。