- 您現在的位置：買賣IC網 > PDF目錄376463 > XRT83SL30 (Exar Corporation) SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR PDF資料下載
參數資料
| 型號： | XRT83SL30 |
| 廠商： | Exar Corporation |
| 英文描述： | SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| 中文描述： | 單通道的T1/E1/J1上海收發器時鐘恢復和抖動衰減器 |
| 文件頁數： | 31/76頁 |
| 文件大?。?/td> | 376K |
| 代理商： | XRT83SL30 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
á
XRT83SL30
SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
PRELIMINARY
REV. P1.0.4
28
TRANSMITTER
T
RANSMIT
T
ERMINATION
M
ODE
In
Hardware
mode, TXTSEL (Pin 45) can be tied “High” to select internal termination mode or tied “Low” for
external termination. In
Host
mode, bit 6 in the appropriate register is set “High” to select the internal
termination mode for the transmit channel, see
Table 19, “Microprocessor Register #1 bit description,” on
page 44
.
For internal termination, the transformer turns ratio is always 1:2. In internal mode, no external resistors are
used. An external capacitor of 0.68
μ
F is used for proper operation of the internal termination circuitry, see
Figure 11
.
E
XTERNAL
T
RANSMIT
T
ERMINATION
M
ODE
By default the XRT83SL30 is set for external termination mode at power up or at
Hardware
reset.
When external transmit termination mode is selected, the internal termination circuitry is disabled. The value of
the external resistors is chosen for a specific application according to the turns ratio selected by TRATIO (Pin
26) in
Hardware
mode or bit 0 in the appropriate register in
Host
mode, see
Table 10
and
Table 21,
“Microprocessor Register #3 bit description,” on page 49
.
Figure 12
is a simplified block diagram for T1 (100
)
in the external termination mode.
Figure 13
is a simplified block diagram for E1 (75
) in the external
termination mode.
F
IGURE
13. S
IMPLIFIED
D
IAGRAM
FOR
E1
IN
E
XTERNAL
T
ERMINATION
M
ODE
(RXTSEL= 0)
T
ABLE
8: T
RANSMIT
T
ERMINATION
C
ONTROL
TXTSEL
TX TERMINATION
T
X
T
RANSFORMER
R
ATIO
0
EXTERNAL
1:2.45
1
INTERNAL
1:2
T
ABLE
9: T
ERMINATION
S
ELECT
C
ONTROL
TERSEL1
TERSEL0
TERMINATION
0
0
100
0
1
110
1
0
75
1
1
120
9.1
9.1
TTIP
TRING
RTIP
RRING
75
XRT83SL30 LIU
75
75
1:2
1:1
相關PDF資料 |
PDF描述 |
|---|---|
| XRT83SL30IV | SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83VSH28 | 8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH28IB | 8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH314 | 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH314IB | 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83SL30ES | 功能描述:外圍驅動器與原件 - PCI 1 CHT1/E1 LIUSH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83SL30IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83SL30IV-F | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT83SL30IVTR-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83SL314 | 制造商:EXAR 制造商全稱:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
發布緊急采購，3分鐘左右您將得到回復。