參數資料
型號： XRT83SL30
廠商： Exar Corporation
英文描述： SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
中文描述： 單通道的T1/E1/J1上海收發器時鐘恢復和抖動衰減器
文件頁數： 18/76頁
文件大?。?/td> 376K
代理商： XRT83SL30
XRT83SL30
SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
REV. P1.0.4
á
PRELIMINARY
15
INSBPV
35
I
Insert Bipolar Violation
In
Hardware Mode
, when this pin transitions from "0" to "1", a bipolar viola-
tion is inserted in the transmitted data stream. Bipolar violation can be
inserted either in the QRSS pattern, or input data when operating in single-
rail mode. The state of this pin is sampled on the rising edge of TCLK.
N
OTE
:
To ensure the insertion of a bipolar violation, this pin should be reset
to a "0" prior to setting to a "1".
NLCD
38
O
Network Loop-Code Detection Output pin
This pin operates differently in the Manual or the Automatic Network Loop-
Code detection modes.
In the Manual Loop-Code detection mode (NLCDE1 =”0” and NLCDE0 =”1”,
or NLCDE1 =”1” and NLCDE0 =”0”) this pin gets set to “1” as soon as the
Loop-Up (“00001”) or Loop-Down (“001”) code is detected in the receive data
for longer than 5 seconds. The NLCD pin stays in the “1” state for as long as
the chip detects the presence of the Loop-Code in the receive data and it is
reset to “0” as soon as it stops receiving it.
When the Automatic Loop-Code detection mode (NLCDE1 =”1” and
NLCDE0 =”1”) is initiated, the NLCD output pin is reset to “0” and the chip is
programmed to monitor the receive input data for the Loop-Up Code. The
NLCD pin is set to a “1” to indicate that the Network Loop Code is detected
for more than 5 seconds. Simultaneously the Remote Loop-Back condition is
automatically activated and the chip is programmed to monitor the receive
data for the Network Loop-Down Code. The NLCD pin stays in the “1” state
for as long as the Remote Loop-Back condition is in effect even if the chip
stops receiving the Loop-Up Code. Remote Loop-Back is removed if the chip
detects the “001” pattern for longer than 5 seconds in the receive data.
Detecting the “001” pattern also results in resetting the NLCD output pin.
AISD
39
O
Alarm Indication Signal Detect Output pin
This pin is set to "1" to indicate that an All Ones Signal is detected by the
receiver. The value of this pin is based on the current status of Alarm Indica-
tion Signal detector.
QRPD
40
O
Quasi-random Pattern Detection Output pin
This pin is set to "1" to indicate that the receiver is currently in synchroniza-
tion with the QRSS pattern. The value of this pin is based on the current sta-
tus of Quasi-random pattern detector.
S
IGNAL
N
AME
P
IN
#
T
YPE
D
ESCRIPTION
相關PDF資料
PDF描述
XRT83SL30IV SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83VSH28 8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT
XRT83VSH28IB 8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT
XRT83VSH314 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
XRT83VSH314IB 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
相關代理商/技術參數
參數描述
XRT83SL30ES 功能描述:外圍驅動器與原件 - PCI 1 CHT1/E1 LIUSH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT83SL30IV 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83SL30IV-F 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT83SL30IVTR-F 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT83SL314 制造商:EXAR 制造商全稱:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*