QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR REV. 1.0.1 50 ALE" />
參數資料
型號： XRT83L34IV-F
廠商： Exar Corporation
文件頁數： 49/99頁
文件大小： 0K
描述： IC LIU T1/E1/J1 QUAD 128TQFP
標準包裝： 72
類型： 線路接口裝置（LIU）
驅動器/接收器數： 4/4
規程： T1，E1，J1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 128-LQFP
供應商設備封裝： 128-TQFP（14x20）
包裝： 托盤
其它名稱： XRT83L34IV-F-ND
xr
XRT83L34
QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR REV. 1.0.1
50
ALE_AS
Address Latch Enable/Address Strobe Input:
The exact function of this input pin depends upon which mode the Microprocessor Interface has been
configured to operate in, as described below.
Intel-Asynchronous Mode - Address Latch Enable - ALE:
If the Microprocessor Interface has been configured to operate in the Intel-Asynchronous Mode, then
this active-high input pin is used to latch the data (residing on the Address Bus, A[6:0] into the Micro-
processor Interface circuitry of the XRT83L34 device and to indicate the start of a READ or WRITE
cycle.
Pulling this input pin "high" enables the input bus drivers for the Address Bus input pins. The contents
of the Address Bus will be latched into the Microprocessor Interface circuitry, upon the falling edge of
this input signal.
Motorola-Asynchronous Mode - Address Strobe - AS*:
If the Microprocessor Interface has been configured to operate in the Motorola-Asynchronous Mode,
then pulling this input pin "LOW enables the "input" bus drivers for the Address Bus Input pins.
During each READ or WRITE operation, the user is expected to drive this input pin "LOW" after (or
around the time that) he/she has places the address (of the "target" register) onto the Address Bus
pins (A[6:0]). The user is then expected to hold this input pin "LOW" for the remainder of the READ or
WRITE cycle.
NOTE: It is permissible to tie the ALE_AS* and CS* input pins together.. Read and Write operations
will be performed properly if ALE_AS is driven "LOW" coincident to whenever CS* is also
driven "LOW".
CS
Chip Select Input:
The user must assert this active-low signal in order to select the Microprocessor Interface for READ
and WRITE operations between the Microprocessor and the XRT83L34 on-chip registers.
RD_DS
Read Strobe/Data Strobe Input Pin:
The exact function of this input pin depends upon which mode the Microprocessor Interface has been
configured to operate in, as described below.
Intel-Asynchronous Mode - READ Strobe Input - RD*:
If the Microprocessor Interface is operating in the Intel-Asynchronous Mode, then this input pin will
function as the RD* (Active-Low READ Strobe) input signal from the Microprocessor. Once this
active-low signal is asserted, then the XRT83L34 device will place the contents of the addressed reg-
ister on the Microprocessor Interface Bi-Directional Data Bus (D[7:0]). When this signal is negated,
then the Data Bus will be tri-stated.
Motorola-Asynchronous Mode - Data Strobe Input - DS*:
If the Microprocessor Interface is operating in the Motorola-Asynchronous Mode, then this input pin
will function as the DS* (Data Strobe) input signal.
.
TABLE 16: MICROPROCESSOR INTERFACE SIGNAL DESCRIPTION
相關PDF資料
PDF描述
XRT83L38IB-F IC LIU T1/E1/J1 OCTAL 225BGA
XRT83SH314IB-F IC LIU T1/E1/J1 14CH 304TBGA
XRT83SH38IB-F IC LIU SH T1/E1/J1 8CH 225BGA
XRT86L30IV-F IC LIU/FRAMER TI/E1/J1 SGL 128LQ
XRT86VL30IV-F IC FRAMR/LIU T1/E1/J1 QD 128LQFP
相關代理商/技術參數
參數描述
XRT83L34IVTR 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT83L34IVTR-F 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT83L38 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83L38_07 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83L38ES 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*