- 您現在的位置：買賣IC網 > PDF目錄203625 > W25Q80VZPIG (WINBOND ELECTRONICS CORP) 1M X 8 SPI BUS SERIAL EEPROM, DSO8 PDF資料下載
參數資料
| 型號： | W25Q80VZPIG |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 1M X 8 SPI BUS SERIAL EEPROM, DSO8 |
| 封裝： | 6 X 5 MM, GREEN, WSON-8 |
| 文件頁數： | 24/61頁 |
| 文件大?。?/td> | 1794K |
| 代理商： | W25Q80VZPIG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
W25Q80, W25Q16, W25Q32
- 30 -
10.2.13 Fast Read Quad I/O (EBh)
The Fast Read Quad I/O (EBh) instruction is similar to the Fast Read Dual I/O (BBh) instruction except
that address and data bits are input and output through four pins IO0, IO1, IO2 and IO3 and four Dummy
clock are required prior to the data output. The Quad I/O dramatically reduces instruction overhead
allowing faster random access for code execution (XIP) directly from the Quad SPI. The Quad Enable
bit (QE) of Status Register-2 must be set to enable the Fast read Quad I/O Instruction. To ensure
optimum performance the High Performance Mode (HPM) instruction (A3h) must be executed once,
prior to the Fast Read Quad I/O Instruction.
The Fast Read Quad I/O instruction can further reduce instruction overhead through setting the Mode
bits (M7-0) after the input Address bits (A23-0), as shown in figure 13a. The upper nibble of the Mode
(M7-4) controls the length of the next Fast Read Quad I/O instruction through the inclusion or exclusion
of the first byte instruction code. The lower nibble bits of the Mode (M3-0) are don’t care (“x”). However,
the IO pins should be high-impedance prior to the falling edge of the first data out clock.
If the Mode bits (M7-0) equals “Ax” hex, then the next Fast Read Quad I/O instruction (after /CS is
raised and then lowered) does not require the EBh instruction code, as shown in figure 13b. This
reduces the instruction sequence by eight clocks and allows the address to be immediately entered
after /CS is asserted low. If the Mode bits (M7-0) are any value other than “Ax” hex, the next instruction
(after /CS is raised and then lowered) requires the first byte instruction code, thus returning to normal
operation. A Mode Bit Reset instruction can be used to reset Mode Bits (M7-0) before issuing normal
instructions (See 10.2.28 for detailed descriptions).
Figure 13a. Fast Read Quad Input/Output Instruction Sequence Diagram (M7-0 = 0xh or NOT Axh)
相關PDF資料 |
PDF描述 |
|---|---|
| W25X16AVDAIZ | 2M X 8 FLASH 2.7V PROM, PDIP8 |
| W25X40AVSSIG | 512K X 8 FLASH 2.7V PROM, PDSO8 |
| W25X80AVDAIZ | 1M X 8 FLASH 2.7V PROM, PDIP8 |
| W25X80ALSSIG | 1M X 8 FLASH 2.7V PROM, PDSO8 |
| W25X40ALDAIZ | 512K X 8 FLASH 2.7V PROM, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W25S243A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 64 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM |
| W25S243A-12 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 64 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM |
| W25S243AD-12 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 64 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM |
| W25S243AF-12 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 64 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM |
| W25X10 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:The W25X10 (1M-bit), W25X20 (2M-bit), W25X40 (4M-bit) and W25X80 (8M-bit) Serial Flash memories provide a storage solution for systems with limited space, pins and power. |
發布緊急采購，3分鐘左右您將得到回復。