- 您現在的位置：買賣IC網 > PDF目錄385009 > TP3410J (NATIONAL SEMICONDUCTOR CORP) TP3410 ISDN Basic Access Echo-Cancelling 2B1Q U Transceiver PDF資料下載
參數資料
| 型號： | TP3410J |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | TP3410 ISDN Basic Access Echo-Cancelling 2B1Q U Transceiver |
| 中文描述： | DATACOM, DIGITAL SLIC, CDIP28 |
| 封裝： | CERAMIC, DIP-28 |
| 文件頁數： | 7/32頁 |
| 文件大?。?/td> | 436K |
| 代理商： | TP3410J |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Functional Description
(Continued)
2.2 Line Transmit Section
Data to be transmitted to the line consists of the customer’s
2B
a
D channel data and the data from the maintenance
processor, plus other ‘‘spare’’ bits in the overhead chan-
nels. This data is multiplexed and scrambled prior to addi-
tion of the syncword. A pulse waveform synthesizer then
drives the transmit filter, which in turn passes the line signal
to the line driver. The differential line-driver outputs, Lo
a
and Lo
b
, are designed to drive a transformer through an
external termination circuit. A 1:1.5 transformer, designed
as shown in the Applications section, results in a signal am-
plitude of nominally 2.5V pk on the line for single quats of
the outer (
g
3) levels. Note, however, that because of the
RDS accumulation of the 2B1Q line code, continuous ran-
dom data will produce signal swings considerably greater
than this on the line. Short-circuit protection is included in
the output stage; overvoltage protection must be provided
externally.
2.3 Line Receive Section
The receive input signal should be derived from the trans-
former by means of a coupling circuit as shown in the Appli-
cations section. At the front-end of the receive section is a
continuous filter followed by a switched-capacitor low-pass
filter, which limits the noise bandwidth. A Hybrid Balance
Filter provides a degree of analog echo-cancellation in or-
der to limit the dynamic range of the composite signal. An
A/D converter then samples the composite received signal
prior to the cancellation of the ‘‘echo’’ from the local trans-
mitter by means of an adaptive digital transversal filter (i.e.,
the ‘‘echo-canceller’’). Following this, the attenuation and
distortion (inter-symbol interference) of the received signal
from the far-end, caused by the transmission line, are equal-
ized by a second adaptive digital filter configured as a Deci-
sion Feedback Equalizer (DFE), thereby restoring a ‘‘flat’’
channel response with maximum received eye opening over
a wide spread of cable attenuation characteristics.
From the received line signal, a Timing Recovery circuit
based on a DPLL (Digital Phase-Locked Loop) recovers a
low-jitter clock for optimum sampling of the received sym-
bols. The MCLK input provides the reference clock for the
DPLL at 15.36 MHz. Received data is then detected, with
automatic correction for line signal polarity if necessary, and
a flywheel synchronization circuit searches for and locks
onto the frame and superframe syncwords. Frame lock will
be maintained until errored sync words are detected for
480 ms. If a loss-of-sync condition persists for 480 ms the
device will cease transmitting and go into a RESET state.
While the receiver is synchronized, data is descrambled us-
ing the specified polynomial, and the individual channels de-
multiplexed and passed to their respective processing cir-
cuits.
Whenever the loop is deactivated, either powered up or
powered down, a Line Signal Detect circuit is enabled to
detect the presence of an incoming 10 kHz wake-up tone if
the far-end starts to activate the loop. The LSD circuit gen-
erates an interrupt and, if the device is powered down, pulls
the LSD pin low; either of these indicators may be used to
alert an external controller, which must respond with the
appropriate commands to initiate the activation sequence
(see the Activation section).
3.0 ACTIVATION CONTROL: OVERVIEW
The TP3410 contains an automatic sequencer for the com-
plete control of the start-up activation sequence specified in
the ANSI standard. Both the ‘‘cold-start’’ and the fast
‘‘warm-start’’ are supported. Interaction with an external
controller requires only Activate Request and Deactivate
Request commands, with the option of inserting breakpoints
in the sequence for additional external control if desired.
Automatic control of the ‘‘a(chǎn)ct’’ and ‘‘dea’’ bits in the M4 bit
positions is provided, along with the specified 40 ms and
480 ms timers used during deactivation. A 15 second de-
fault timer is also included, to prevent system lock-up in the
event of a failed activation attempt. Section 11 gives an
overview of the activation handshake between the TP3410
and the controller. See TP3410 User’s Manual AN-913 for
additional information.
4.0 MAINTENANCE FUNCTIONS: OVERVIEW
4.1 M Channel Processing
In each frame of the superframe there are 6 ‘‘Overhead’’
bits assigned to various control and maintenance functions
of the DSL. Some processing of these bits may be pro-
grammed via the Command Registers, while interaction with
an external controller provides the flexibility to take full ad-
vantage of the maintenance channels. New data written to
any of the overhead bit Transmit Registers is resynchroniz-
ed internally to the next available complete superframe or
half-superframe, as appropriate. In addition, the SFS pin
may be used to indicate the start of each superframe in 1
direction, see Figure 2 and Register CR2.
TL/H/9151–26
FIGURE 2. Superframe Sync Pin Timing
7
相關PDF資料 |
PDF描述 |
|---|---|
| TP3420AJ | ISDN S/T Interface Device |
| TP3420A | ISDN S/T Interface Device |
| TP3420AN | ISDN S/T Interface Device |
| TP3420AV | ISDN S/T Interface Device |
| TP3464 | MICROWIRE⑩ Interface Device (MID) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TP3410J304 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC-ISDN TRANSCEIVER |
| TP3410J-304 | 制造商:Texas Instruments 功能描述:ISDN LINE INTERFACE, BASIC, 28 Pin, Ceramic, DIP |
| TP3410J304/NOPB | 功能描述:IC TRANSCEIVER MONOLITHIC 28CDIP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| TP3410J304-X | 功能描述:IC TXRX ISDN BASIC ACC 28-CERDIP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| TP3410N304 | 制造商:OC White Company 功能描述:ISDN U HDLC Interface 1-Line 160Kbps 5V 28-Pin CDIP |
發布緊急采購，3分鐘左右您將得到回復。