參數資料
型號： TMS32C5402PGER10G4
廠商： Texas Instruments, Inc.
元件分類： 數字信號處理
英文描述： FIXED-POINT DIGITAL SIGNAL PROCESSOR
中文描述： 定點數字信號處理器
文件頁數： 10/68頁
文件大?。?/td> 948K
代理商： TMS32C5402PGER10G4
SPRS079E – OCTOBER 1998 – REVISED AUGUST 2000
10
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251–1443
Terminal Functions (Continued)
NAME
DESCRIPTION
TYPE
TERMINAL
HOST-PORT INTERFACE SIGNALS (CONTINUED)
HBIL
I
Byte identification. HBIL identifies the first or second byte of transfer. The HBIL input has an internal pullup
resistor that is only enabled when HPIENA = 0.
HCS
I
Chip select. HCS is the select input for the HPI and must be driven low during accesses. The chip-select input
has an internal pullup resistor that is only enabled when HPIENA = 0.
HDS1
HDS2
I
Data strobe. HDS1 and HDS2 are driven by the host read and write strobes to control transfers. The strobe inputs
have internal pullup resistors that are only enabled when HPIENA = 0.
HAS
I
Address strobe. Hosts with multiplexed address and data pins require HAS to latch the address in the HPIA
register. HAS has an internal pullup resistor that is only enabled when HPIENA = 0.
HR/W
I
Read/write. HR/W controls the direction of an HPI transfer. R/W has an internal pullup resistor that is only
enabled when HPIENA = 0.
HRDY
O/Z
Ready. The ready output informs the host when the HPI is ready for the next transfer. HRDY goes into the
high-impedance state when OFF is low.
Host interrupt. This output is used to interrupt the host. When the DSP is in reset, HINT is driven high
.
HINT can
also be configured as the timer 1 output (TOUT1), when the HPI is disabled. The signal goes into the
high-impedance state when OFF is low.
HINT
O/Z
HPIENA
I
HPI module select. HPIENA must be driven high during reset to enable the HPI. An internal pulldown resistor
is always active and the HPIENA pin is sampled on the rising edge of RS. If HPIENA is left open or is driven low
during reset, the HPI module is disabled. Once the HPI is disabled, the HPIENA pin has no effect until the ’5402
is reset.
SUPPLY PNS
CVDD
DVDD
VSS
S
+VDD. Dedicated 1.8-V power supply for the core CPU
+VDD. Dedicated 3.3-V power supply for the I/O pins
Ground
S
S
TEST PINS
TCK
I
IEEE standard 1149.1 test clock. TCK is normally a free-running clock signal with a 50% duty cycle. The changes
on the test access port (TAP) of input signals TMS and TDI are clocked into the TAP controller, instruction
register, or selected test data register on the rising edge of TCK. Changes at the TAP output signal (TDO) occur
on the falling edge of TCK.
TDI
I
IEEE standard 1149.1 test data input pin with internal pullup device. TDI is clocked into the selected register
(instruction or data) on a rising edge of TCK.
TDO
O/Z
IEEE standard 1149.1 test data output. The contents of the selected register (instruction or data) are shifted out
of TDO on the falling edge of TCK. TDO is in the high-impedance state except when the scanning of data is in
progress. TDO also goes into the high-impedance state when OFF is low.
TMS
I
IEEE standard 1149.1 test mode select. Pin with internal pullup device. This serial control input is clocked into
the TAP controller on the rising edge of TCK.
TRST
I
IEEE standard 1149.1 test reset. TRST, when high, gives the IEEE standard 1149.1 scan system control of the
operations of the device. If TRST is not connected or is driven low, the device operates in its functional mode,
and the IEEE standard 1149.1 signals are ignored. Pin with internal pulldown device.
I = input, O = output, Z = high impedance, S = supply
All revisions of the ’5402 can be operated with an external clock source, provided that the proper voltage levels be driven on the X2/CLKIN
pin. It should be noted that the X2/CLKIN pin is referenced to the device 1.8V power supply (CVDD), rather than the 3V I/O supply (DVDD).
Refer to the recommended operating conditions section of this document for the allowable voltage levels of the X2/CLKIN pin.
相關PDF資料
PDF描述
TMS34020 GRAPHICS PROCESSORS
TMS3450NL LED DUPLEX DIGITAL RADIO CLOCK
TMS3471CFS 780- 】 488-pixel ccd image sensor
TMS3471 2/3-INCH NTSC TIMER
TMS3473 PARALLEL DRIVER
相關代理商/技術參數
參數描述
TMS32C6202BGNZA250 功能描述:數字信號處理器和控制器 - DSP, DSC Fixed-Pt Dig Signal Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS32C6203BGLS173A 制造商:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSOR - Trays
TMS32C6203BGLS173H 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述:DSP FIX PT 16BIT 173MHZ 1384MIPS 384PIN FC/CSP - Trays
TMS32C6203BGNY17-3 制造商:Texas Instruments 功能描述:TMS C6203B 1.7V REV 2.X GNY 300 MHZ - Trays
TMS32C6203BGNZA250 功能描述:數字信號處理器和控制器 - DSP, DSC Fixed-Point Dig Sig Processor RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*