
Index
IX-9
TolerANT technology
1-6
transfer (SXFER)
4-34
Ultra3 SCSI
2-23
valid (VAL)
4-39
wide residue (SWIDE)
4-79
SCSI-1
transfers
(single-ended 5.0 Mbytes)
6-61
SCSI-2
fast transfers
10.0 Mbytes (8-bit transfers)
40 MHz Clock
6-63
40 MHz clock
6-61
20.0 Mbytes (16-bit transfers)
40 MHz clock
6-61
,
6-63
second dword
5-14
,
5-22
,
5-24
,
5-33
,
5-36
,
5-39
select
2-19
during selection
2-42
instruction
5-17
with ATN/
5-21
with SATN/ on a start sequence (WATN)
4-26
selected (SEL)
4-72
,
4-76
selection or reselection time-out (STO)
4-74
,
4-78
selection response logic test (SLT)
4-85
semaphore (SEM)
4-49
serial EEPROM
data format
2-63
interface
2-62
SERR/
3-13
SERR/ enable (SE)
4-4
set instruction
5-16
,
5-18
set/clear
carry
5-21
SACK/
5-22
SATN/
5-22
target mode
5-21
shadow register test mode (SRTM)
4-57
SIDL
least significant byte full (ILF)
4-43
most significant byte full (ILF1)
4-46
signal names
and BGA position
3-6
by BGA position
3-6
signal process (SIGP)
4-48
,
4-54
signaled system error (SSE)
4-5
simple arbitration
4-24
single
address cycles
2-22
ended SCSI signals
6-7
step interrupt (SSI)
4-41
,
4-67
step mode (SSM)
4-69
SIP
2-52
,
2-53
slow memory ( 128 Kbytes)
read cycle
6-52
write cycle
6-54
slow ROM pin
3-27
SODL
least significant byte full (OLF)
4-43
most significant byte full (OLF1)
4-46
software reset (SRST)
4-48
source
I/O-memory enable (SIOM)
4-65
special cycle command
2-5
SREQ
2-53
stacked interrupts
2-52
start
address
5-14
,
5-22
DMA operation (STD)
4-69
sequence (START)
4-25
static block move selector (SBMS)
4-101
STOP command
2-10
stop signal
3-12
STOP/
3-12
store instruction
2-32
stress ratings
6-1
subsystem ID
2-63
(SID[15:0])
4-13
subsystem vendor ID
2-63
(SVID[15:0])
4-12
SYM53C1010
329 ball grid array
6-67
329 BGA mechanical drawing
6-68
new features
1-4
SYM53C1010-33
register map
A-1
SYM53C896
register map
A-2
SYNC_IRQD (SI)
4-51
synchronous
clock conversion factor (SCF[2:0])
4-32
data transfer rates
2-43
operation
2-43
SCSI receive
2-40
SCSI send
2-40
system error
3-13
system signals
3-9
T
table indirect
5-7
,
5-20
mode
5-19
table relative
5-20
target
asynchronous receive
6-60
asynchronous send
6-59
mode
5-10
,
5-15
SATN/ active (M/A)
4-75
mode (TRG)
4-27
ready
3-11
synchronous transfer
6-63
,
6-66
timing
6-15
TCK
3-24
TDI
3-24
TDO
3-24
TEMP register
5-37
temporary (TEMP)
4-56
termination
2-41
test clock
3-24
test data in
3-24
test data out
3-24
test halt SCSI clock
3-24
test interface signals
3-24
test mode select
3-24
test power down
3-24
test reset
3-24
TEST_HSC
3-24
TEST_PD
3-24
TEST_RSTN
3-24
third dword
5-14
,
5-33
,
5-36
timer test mode (TTM)
4-90
TMS
3-24
TolerANT
1-6