
REGISTERDESCRIPTION
(continued)
Index Register16 :
Modem Codec #2
Output Control
4
3
7
6
5
2
1
0
0
0
0
0
M
-
-
-
-M2TX1 : Reset value : 0. Setting this bit to 1 will
enable the mono codec #2 DAC output
to the HandTx1 output Pin. Setting the
bit to 0 will mute the signal.
-M2TX2 : Reset value : 0. Setting this bit to 1 will
enable the mono codec #2 DAC output
to the HandTx2 output Pin. Setting the
bit to 0 will mute the signal.
-M2TX3 : Reset value : 0. Setting this bit to 1 will
enable the mono codec #2 DAC output
to the HandTx3 output Pin. Setting the
bit to 0 will mute the signal.
M2TXG : Reset value : 0. Setting this bit to 1 will
place a -6dB attenuator in the output
DAC path. Setting thisbit to0 willresult
in a gainpath of 0dB.
Table 10 :
Transmit Gain (A2)
M2TXG
Transmit Amplifier Gain (A2)
0
1
+0dB
-6dB
Index Register17 :
LoopbackControlRegister
7
6
5
4
3
2
1
0
0
0
0
0
+
+
+
+
+LOOPR : Resetvalue :0.Settingthisbitto1will
loop the ADC digital data to the DAC
converter on the audio codec right
converter. Setting this bit to 0 will
cause the DAC converter to receive
its digital data from the serial port
whichis normaloperation.
+LOOPL
: Reset value : 0. Setting this bit to 1
will loop the ADC digital data to the
DACconverterontheaudiocodecleft
converter. Setting this bit to 0 will
cause the DAC converter to receive
its digital data from the serial port
whichis normaloperation.
+LOOPM1: Reset value : 0. Setting this bit to 1
will loop the ADC digital data to the
DAC converteron themonocodec#1
converter. Setting this bit to 0 will
cause the DAC converter to receive
its digital data from the serial port
which is normal operation.
+LOOPM2: Reset value : 0. Setting this bit to 1
will loop the ADC digital data to the
DAC converteron themonocodec#2
converter. Setting this bit to 0 will
cause the DAC converter to receive
its digital data from the serial port
which is normal operation.
Index Register 18 :
GPIO ConfigurationRegister
7
6
5
4
3
2
1
0
C
C
C
C
C
C
C
C
CFGPIO0 : Reset value : 0. If this bit is set to 0,
then the Pin GPIO0is an input.If this
bitissetto 1,thenthePinisan output.
CFGPIO1 : Reset value : 0. If this bit is set to 0,
then the Pin GPIO1is an input.If this
bitissetto 1,thenthePinisan output.
CFGPIO2 : Reset value : 0. If this bit is set to 0,
then the Pin GPIO2is an input.If this
bitissetto 1,thenthePinisan output.
CFGPIO3 : Reset value : 0. If this bit is set to 0,
then the Pin GPIO3is an input.If this
bitissetto 1,thenthePinisan output.
CFGPIO4 : Reset value : 0. If this bit is set to 0,
then the Pin GPIO4is an input.If this
bitissetto 1,thenthePinisan output.
CFGPIO5 : Reset value : 0. If this bit is set to 0,
then the Pin GPIO5is an input.If this
bitissetto 1,thenthePinisan output.
CFGPIO6 : Reset value : 0. If this bit is set to 0,
then the Pin GPIO6is an input.If this
bitissetto 1,thenthePinisan output.
CFGPIO7 : Reset value : 0. If this bit is set to 0,
then the Pin GPIO7is an input.If this
bitis setto 1, thenthepinis an output.
STLC7549
32/35