- 您現在的位置：買賣IC網 > PDF目錄98142 > SST89C58-33-I-TQJE (SILICON STORAGE TECHNOLOGY INC) 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQFP44 PDF資料下載
參數資料
| 型號： | SST89C58-33-I-TQJE |
| 廠商： | SILICON STORAGE TECHNOLOGY INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQFP44 |
| 封裝： | LEAD FREE, TQFP-44 |
| 文件頁數： | 19/52頁 |
| 文件大?。?/td> | 967K |
| 代理商： | SST89C58-33-I-TQJE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
26
Data Sheet
FlashFlex51 MCU
SST89C54 / SST89C58
2004 Silicon Storage Technology, Inc.
S71131-04-000
6/04
The Byte-Verify command allows the user to verify that the
SST89C54/58 has correctly performed an Erase or Pro-
gram command. Byte-Verify command returns the data
byte in SFDT. The user is required to check that the previ-
ous Flash operation has fully completed before issuing a
Byte-Verify. Byte-Verify command execution time is short
enough that there is no need to poll for command comple-
tion and no interrupt is generated. The Byte-Verify com-
mand sequence is as follows:
Prog-SB3, Prog-SB2, Prog-SB1 commands are used to
program the Security bits (see Table 8-1). Upon completion
of any of those commands, the security options will be
updated immediately.
Security bits previously in un-programmed state can be
programmed by these commands. The Prog-SB3, Prog-
SB2, Prog-SB1 sequences are as follows:
Prog-RB1, Prog-RB0 commands are used to program the
RE-MAP[1:0] bits (see Table 3-1). These commands only
change the RE-MAP[1:0] bits and have no effect on Map-
En[1:0] until after a reset cycle. Therefore, the effect of
these commands is not immediate.
Re-Map bits previously in un-programmed state can be
programmed by these commands. The Prog-RB1, Prog-
RB0 sequences are as follows:
Prog-SB3, Prog-SB2, Prog-SB1, Prog-RB1, and Prog-RB0
commands must reside only in Block 0 (32 KByte block) or
external code memory.
Any such instructions issued from Block 1 may cause
unpredictable program behavior.
4.2.4 Polling
A command that uses the polling method to detect flash
operation completion should poll on the Flash_busy bit
(SFST[2]). When Flash_busy de-asserts (logic 0), the
device is ready for the next operation.
The BUSY bit (SFST[3]) is provided for Burst-Program. In
between bytes within a burst sequence, the Busy bit will
become logic 0 to indicate that the next Burst-Program byte
should be presented. Completion of the full burst cycle is
indicated also by Flash_busy bit (SFST[2]).
MOVC instruction may also be used for verification of the
Programming and Erase operation of the flash memory.
MOVC instruction will fail if it is directed at a flash block that
is still busy.
MOV SFCM, #0CH
SFDT register
contains data
Load byte address
MOV SFAH, #byte_addressH
MOV SFAL, #byte_addressL
1131 F13.0
IAP Enable
ORL SFCF, #40H
Set-Up
MOV SFAH, #80H
MOV SFDT, #55H
OR
INT1# Interrupt
indicates completion
Polling SFST[2]
indicates completion
Program SB2
MOV SFCM, #03H
or
MOV SFCM, #83H
Program SB1
MOV SFCM, #0FH
or
MOV SFCM, #8FH
Program SB3
MOV SFCM, #05H
or
MOV SFCM, #85H
1131 F14.0
IAP Enable
ORL SFCF, #40H
OR
Set-Up
MOV SFAH, #80H
MOV SFDT, #55H
OR
INT1# Interrupt
indicates completion
Polling SFST[2]
indicates completion
Program Re-Map [1]
MOV SFCM, #09H
or
MOV SFCM, #89H
Program Re-Map [0]
MOV SFCM, #08H
or
MOV SFCM, #88H
1131 F15.0
IAP Enable
ORL SFCF, #40H
相關PDF資料 |
PDF描述 |
|---|---|
| SST89E516RD-40-C-QIF | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, QCC40 |
| SST89E516RD2-40-C-NJE | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQCC44 |
| SST89E52RD-40-C-PI | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PDIP40 |
| SST89V58RD-33-C-PI | 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PDIP40 |
| SST89V58RD-33-I-PIE | 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PDIP40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SST89C58RC-40-C-QIF | 功能描述:8位微控制器 -MCU 34K (32Kx8K) SM-Bus 40MHz 2.7-5.5V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| SST89C58RC-40-C-QIF-T | 功能描述:8位微控制器 -MCU 4.5-5.5V FlashFlex 8b 8051 Microctrl RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| SST89C58RC-40-I-NJE | 制造商:Microchip Technology Inc 功能描述:8 BIT MICROCONTROLLER WITH 40K - Rail/Tube 制造商:Microchip Technology Inc 功能描述:Microchip SST89C58RC-40-I-NJE Microcontrollers (MCU) |
| SST89C58RC-40-I-QIF | 功能描述:8位微控制器 -MCU 40K (32Kx8K) SM-Bus 40MHz 2.7-5.5V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| SST89C58RC-40-I-TQJE | 功能描述:8位微控制器 -MCU 40K (32Kx8K) SM-Bus 40MHz 2.7-5.5V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。