- 您現在的位置：買賣IC網 > PDF目錄98076 > SAH-C515A-4R (INFINEON TECHNOLOGIES AG) 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | SAH-C515A-4R |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | METRIC, PLASTIC, QFP-80 |
| 文件頁數： | 164/182頁 |
| 文件大?。?/td> | 1917K |
| 代理商： | SAH-C515A-4R |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁當前第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁
Semiconductor Group
6-31
1997-08-01
On-Chip Peripheral Components
C515A
6.2.2.3
Compare Function of Registers CRC, CC1 to CC3
The compare function of a timer/register combination can be described as follows. The 16-bit value
stored in a compare/capture register is compared with the contents of the timer register. lf the count
value in the timer register matches the stored value, an appropriate output signal is generated at a
corresponding port pin, and an interrupt is requested.
The contents of a compare register can be regarded as ’time stamp’ at which a dedicated output
reacts in a predefined way (either with a positive or negative transition). Variation of this ’time stamp’
somehow changes the wave of a rectangular output signal at a port pin. This may - as a variation
of the duty cycle of a periodic signal - be used for pulse width modulation as well as for a continually
controlled generation of any kind of square wave forms. Two compare modes are implemented to
cover a wide range of possible applications.
The compare modes 0 and 1 are selected by bit T2CM in special function register T2CON. In both
compare modes, the new value arrives at the port pin 1 within the same machine cycle in which the
internal compare signal is activated.
The four registers CRC, CC1 to CC3 are multifunctional as they additionally provide a capture,
compare or reload capability (the CRC register only). A general selection of the function is done in
register CCEN. Please note that the compare interrupt CC0 can be programmed to be negative or
positive transition activated. The internal compare signal (not the output signal at the port pin!) is
active as long as the timer 2 contents is equal to the one of the appropriate compare registers, and
it has a rising and a falling edge. Thus, when using the CRC register, it can be selected whether an
interrupt should be caused when the compare signal goes active or inactive, depending on bit I3FR
in T2CON. For the CC registers 1 to 3 an interrupt is always requested when the compare signal
goes active (see figure 6-16).
6.2.2.3.1
Compare Mode 0
In mode 0, upon matching the timer and compare register contents, the output signal changes from
low to high. lt goes back to a low level on timer overflow. As long as compare mode 0 is enabled,
the appropriate output pin is controlled by the timer circuit only, and not by the user. Writing to the
port will have no effect. Figure 6-15 shows a functional diagram of a port latch in compare mode 0.
The port latch is directly controlled by the two signals timer overflow and compare. The input line
from the internal bus and the write-to-latch line are disconnected when compare mode 0 is enabled.
Compare mode 0 is ideal for generating pulse width modulated output signals, which in turn can be
used for digital-to-analog conversion via a filter network or by the controlled device itself (e.g. the
inductance of a DC or AC motor). Mode 0 may also be used for providing output clocks with initially
defined period and duty cycle. This is the mode which needs the least CPU time. Once set up, the
output goes on oscillating without any CPU intervention. Figure 6-16 and 6-17 illustrate the function
of compare mode 0.
相關PDF資料 |
PDF描述 |
|---|---|
| SAH-C515C-LM | 8-BIT, 10 MHz, MICROCONTROLLER, PQFP80 |
| SAH-XC2210U-8F66R | 32-BIT, FLASH, 66 MHz, RISC MICROCONTROLLER, PDSO38 |
| SAH-XC2387A-104F80L | 16-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144 |
| SAH-XC2387C-200F100L | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP144 |
| SAH-XC2387C-136F100L | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAH-C517A | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-bit CMOS MICROCONTROLLER |
| SAHC684M50R501 | 制造商:SHARMA 制造商全稱:Sharma Electro Components,Inc 功能描述:Tantalum Capacitors |
| SAHC685M20R501 | 制造商:SHARMA 制造商全稱:Sharma Electro Components,Inc 功能描述:Tantalum Capacitors |
| SAHD106M25R501 | 制造商:SHARMA 制造商全稱:Sharma Electro Components,Inc 功能描述:Tantalum Capacitors |
| SAHD155M50R501 | 制造商:SHARMA 制造商全稱:Sharma Electro Components,Inc 功能描述:Tantalum Capacitors |
發布緊急采購，3分鐘左右您將得到回復。