- 您現在的位置：買賣IC網 > PDF目錄98076 > SAH-C515A-4R (INFINEON TECHNOLOGIES AG) 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | SAH-C515A-4R |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | METRIC, PLASTIC, QFP-80 |
| 文件頁數： | 14/182頁 |
| 文件大?。?/td> | 1917K |
| 代理商： | SAH-C515A-4R |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁
Semiconductor Group
6-59
1997-08-01
On-Chip Peripheral Components
C515A
6.4
A/D Converter
The C515A includes a high performance / high speed 10-bit A/D-Converter (ADC) with 8 analog
input channels. It operates with a successive approximation technique and uses self calibration
mechanisms for reduction and compensation of offset and linearity errors. The A/D converter
provides the following features:
– 8 multiplexed input channels (port 6), which can also be used as digital inputs
– 10-bit resolution
– Single or continuous conversion mode
– Internal or external start-of-conversion trigger capability
– Interrupt request generation after each conversion
– Using successive approximation conversion technique via a capacitor array
– Built-in hidden calibration of offset and linearity errors
The externally applied reference voltage range has to be held on a fixed value within the
specifications. The main functional blocks of the A/D converter are shown in figure 6-31.
6.4.1
A/D Converter Operation
An internal start of a single A/D conversion is triggered by a write-to-ADDATL instruction. When
single conversion mode is selected (bit ADM=0) only one A/D conversion is performed. In
continuous mode (bit ADM=1), after completion of an A/D conversion a new A/D conversion is
triggered automatically until bit ADM is reset.
An externally controlled conversion can be achieved by setting the bit ADEX. In this mode one
single A/D conversion is triggered by a 1-to-0 transition at pin P4.0/ADST (when ADM is 0). P4.0/
ADST is sampled during S5P2 of every machine cycle. When the samples show a logic high in one
cycle and a logic low in the next cycle the transition is detected and the A/D conversion is started.
When ADM and ADEX is set, a continuous conversion is started when pin P4.0/ADST sees a low
level. Only if no A/D conversion (single or continuous) has occurred after the last reset operation, a
1-to-0 transition is required at pin P4.0/ADST for starting the continuous conversion mode
externally. The continuous A/D conversion is stopped when the pin P4.0/ADST goes back to high
level. The last running A/D conversion during P4.0/ADST low level will be completed.
The busy flag BSY (ADCON0.4) is automatically set when an A/D conversion is in progress. After
completion of the conversion it is reset by hardware. This flag can be read only, a write has no
effect. The interrupt request flag IADC (IRCON.0) is set when an A/D conversion is completed.
The bits MX0 to MX2 in special function register ADCON0 and ADCON1 are used for selection of
the analog input channel. The bits MX0 to MX2 are represented in both registers ADCON0 and
ADCON1; however, these bits are present only once. Therefore, there are two methods of selecting
an analog input channel : If a new channel is selected in ADCON1 the change is automatically done
in the corresponding bits MX0 to MX2 in ADCON0 and vice versa.
Port 6 is a dual purpose input port. lf the input voltage meets the specified logic levels, it can also
be used as digital inputs regardless of whether the pin levels are sampled by the A/D converter at
the same time.
相關PDF資料 |
PDF描述 |
|---|---|
| SAH-C515C-LM | 8-BIT, 10 MHz, MICROCONTROLLER, PQFP80 |
| SAH-XC2210U-8F66R | 32-BIT, FLASH, 66 MHz, RISC MICROCONTROLLER, PDSO38 |
| SAH-XC2387A-104F80L | 16-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144 |
| SAH-XC2387C-200F100L | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP144 |
| SAH-XC2387C-136F100L | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAH-C517A | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-bit CMOS MICROCONTROLLER |
| SAHC684M50R501 | 制造商:SHARMA 制造商全稱:Sharma Electro Components,Inc 功能描述:Tantalum Capacitors |
| SAHC685M20R501 | 制造商:SHARMA 制造商全稱:Sharma Electro Components,Inc 功能描述:Tantalum Capacitors |
| SAHD106M25R501 | 制造商:SHARMA 制造商全稱:Sharma Electro Components,Inc 功能描述:Tantalum Capacitors |
| SAHD155M50R501 | 制造商:SHARMA 制造商全稱:Sharma Electro Components,Inc 功能描述:Tantalum Capacitors |
發布緊急采購，3分鐘左右您將得到回復。