參數資料
型號： S29GL256N10FFI010
廠商： SPANSION LLC
元件分類： PROM
英文描述： MirrorBit Flash Family
中文描述： 16M X 16 FLASH 3V PROM, 100 ns, PBGA64
封裝： 13 X 11 MM, LEAD FREE, FBGA-64
文件頁數： 53/95頁
文件大?。?/td> 3781K
代理商： S29GL256N10FFI010
May 30, 2008 S29GL-N_00_B8
S29GL-N
57
Data
She e t
9.11
Password Protection Command Set Definitions
The Password Protection Command Set permits the user to program the 64-bit password, verify the
programming of the 64-bit password, and then later unlock the device by issuing the valid 64-bit password.
The Password Protection Command Set Entry command sequence must be issued prior to any of the
commands listed following to enable proper command execution.
Note that issuing the Password Protection Command Set Entry command disabled reads and writes the
main memory.
Password Program Command
Password Read Command
Password Unlock Command
The Password Program command permits programming the password that is used as part of the hardware
protection scheme. The actual password is 64-bits long. There is no special addressing order required for
programming the password. The password is programmed in 8-bit or 16-bit portions. Each portion
requires a Password Program Command.
Once the Password is written and verified, the Password Protection Mode Lock Bit in the Lock Register must
be programmed in order to prevent verification. The Password Program command is only capable of
programming 0s. Programming a 1 after a cell is programmed as a 0 results in a time-out by the Embedded
Program AlgorithmTM with the cell remaining as a 0. The password is all F’s when shipped from the factory. All
64-bit password combinations are valid as a password.
The Password Read command is used to verify the Password. The Password is verifiable only when the
Password Protection Mode Lock Bit in the Lock Register is not programmed. If the Password Protection
Mode Lock Bit in the Lock Register is programmed and the user attempts to read the Password, the device
always drives all F’s onto the DQ data bus.
The lower two address bits (A1–A0) for word mode and (A1–A-1) for by byte mode are valid during the
Password Read, Password Program, and Password Unlock commands. Writing a 1 to any other address
bits (AMAX-A2) aborts the Password Read and Password Program commands.
The Password Unlock command is used to clear the PPB Lock Bit to the unfreeze state so that the PPB bits
can be modified. The exact password must be entered in order for the unlocking function to occur. This 64-bit
Password Unlock command sequence takes at least 2 s to process each time to prevent a hacker from
running through the all 64-bit combinations in an attempt to correctly match the password. If another
password unlock is issued before the 64-bit password check execution window is completed, the command is
ignored. If the wrong address or data is given during password unlock command cycle, the device may enter
the write-to-buffer abort state. In order to exit the write-to-abort state, the write-to-buffer-abort-reset command
must be given. Otherwise the device hangs.
The Password Unlock function is accomplished by writing Password Unlock command and data to the device
to perform the clearing of the PPB Lock Bit to the unfreeze state. The password is 64 bits long. A1 and A0 are
used for matching in word mode and A1, A0, A-1 in byte mode. Writing the Password Unlock command does
not need to be address order specific. An example sequence is starting with the lower address A1-A0=00,
followed by A1-A0=01, A1-A0=10, and A1-A0=11 if the device is configured to operate in word mode.
Approximately 2 s is required for unlocking the device after the valid 64-bit password is given to the device.
It is the responsibility of the microprocessor to keep track of the entering the portions of the 64-bit password
with the Password Unlock command, the order, and when to read the PPB Lock bit to confirm successful
password unlock. In order to re-lock the device into the Password Protection Mode, the PPB Lock Bit Set
command can be re-issued.
Note: The Password Protection Command Set Exit command must be issued after the execution of the
commands listed previously to reset the device to read mode. Otherwise the device hangs.
Note: Issuing the Password Protection Command Set Exit command re-enables reads and writes for the
main memory.
相關PDF資料
PDF描述
S29GL256N80FAI010 MirrorBit Flash Family
S29GL256N80FFI010 MirrorBit Flash Family
S29GL256N80FFI013 MirrorBit Flash Family
S29JL032H90TAI223 2M X 16 FLASH 3V PROM, 90 ns, PDSO48
S29WS064N0PBAW011 256/128/64 MEGABIT CMOS 1.8 VOLT ONLY SIMULTANEOUS READ/WRITE BURST MODE FLASH MEMORY
相關代理商/技術參數
參數描述
S29GL256N10FFI012 制造商:Spansion 功能描述:Flash - NOR IC
S29GL256N10FFI020 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 256Mbit 32M/16M x 8bit/16bit 100ns 64-Pin Fortified BGA Tray 制造商:Spansion 功能描述:MIRRORBIT FLASH 256MB SMD 29LV256
S29GL256N10TFI010 功能描述:IC FLASH 制造商:cypress semiconductor corp 系列:GL-N 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:256Mb （32M x 8，16M x 16） 寫周期時間 - 字，頁:100ns 訪問時間:100ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:56-TFSOP（0.724"，18.40mm 寬） 供應商器件封裝:56-TSOP 標準包裝:91
S29GL256N11FAI010 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 256M-Bit 32M x 8/16M x 16 110ns 64-Pin Fortified BGA Tray
S29GL256N11FAIIH2 制造商:Spansion 功能描述:S29GL256N11FAIIH2 - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*