參數資料
型號： S29GL256N10FFI010
廠商： SPANSION LLC
元件分類： PROM
英文描述： MirrorBit Flash Family
中文描述： 16M X 16 FLASH 3V PROM, 100 ns, PBGA64
封裝： 13 X 11 MM, LEAD FREE, FBGA-64
文件頁數： 52/95頁
文件大?。?/td> 3781K
代理商： S29GL256N10FFI010
56
S29GL-N
S29GL-N_00_B8 May 30, 2008
Da ta
Sh e e t
9.9
Erase Suspend/Erase Resume Commands
The Erase Suspend command, B0h, allows the system to interrupt a sector erase operation and then read
data from, or program data to, any sector not selected for erasure. This command is valid only during the
sector erase operation, including the 50 s time-out period during the sector erase command sequence. The
Erase Suspend command is ignored if written during the chip erase operation or Embedded Program
algorithm.
When the Erase Suspend command is written during the sector erase operation, the device requires a typical
of 5
μs (maximum of 20 μs) to suspend the erase operation. However, when the Erase Suspend command is
written during the sector erase time-out, the device immediately terminates the time-out period and suspends
the erase operation.
After the erase operation is suspended, the device enters the erase-suspend-read mode. The system can
read data from or program data to any sector not selected for erasure. (The device erase suspends all
sectors selected for erasure.) Reading at any address within erase-suspended sectors produces status
information on DQ7–DQ0. The system can use DQ7, or DQ6 and DQ2 together, to determine if a sector is
actively erasing or is erase-suspended. Refer to the Write Operation Status section for information on these
status bits.
After an erase-suspended program operation is complete, the device returns to the erase-suspend-read
mode. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just
as in the standard word program operation. Refer to Write Operation Status on page 64 for more information.
In the erase-suspend-read mode, the system can also issue the autoselect command sequence. Refer to the
To resume the sector erase operation, the system must write the Erase Resume command. The address of
the erase-suspended sector is required when writing this command. Further writes of the Resume command
are ignored. Another Erase Suspend command can be written after the chip has resumed erasing. It is
important to allow an interval of at least 5 ms between Erase Resume and Erase Suspend.
9.10
Lock Register Command Set Definitions
The Lock Register Command Set permits the user to one-time program the Secured Silicon Sector Protection
Bit, Persistent Protection Mode Lock Bit, and Password Protection Mode Lock Bit. The Lock Register bits are
all readable after an initial access delay.
The Lock Register Command Set Entry command sequence must be issued prior to any of the following
commands listed, to enable proper command execution.
Note that issuing the Lock Register Command Set Entry command disables reads and writes for the
flash memory.
Lock Register Program Command
Lock Register Read Command
The Lock Register Command Set Exit command must be issued after the execution of the commands to
reset the device to read mode. Otherwise the device hangs. If this happens, the flash device must be reset.
Please refer to RESET# for more information. It is important to note that the device is in either Persistent
Protection mode or Password Protection mode depending on the mode selected prior to the device hang.
For either the Secured Silicon Sector to be locked, or the device to be permanently set to the Persistent
Protection Mode or the Password Protection Mode, the associated Lock Register bits must be programmed.
Note that only the Persistent Protection Mode Lock Bit or the Password Protection Mode Lock Bit can be
programmed. The Lock Register Program operation aborts if there is an attempt to program both the
Persistent Protection Mode and the Password Protection Mode Lock bits.
The Lock Register Command Set Exit command must be initiated to re-enable reads and writes to the main
memory.
相關PDF資料
PDF描述
S29GL256N80FAI010 MirrorBit Flash Family
S29GL256N80FFI010 MirrorBit Flash Family
S29GL256N80FFI013 MirrorBit Flash Family
S29JL032H90TAI223 2M X 16 FLASH 3V PROM, 90 ns, PDSO48
S29WS064N0PBAW011 256/128/64 MEGABIT CMOS 1.8 VOLT ONLY SIMULTANEOUS READ/WRITE BURST MODE FLASH MEMORY
相關代理商/技術參數
參數描述
S29GL256N10FFI012 制造商:Spansion 功能描述:Flash - NOR IC
S29GL256N10FFI020 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 256Mbit 32M/16M x 8bit/16bit 100ns 64-Pin Fortified BGA Tray 制造商:Spansion 功能描述:MIRRORBIT FLASH 256MB SMD 29LV256
S29GL256N10TFI010 功能描述:IC FLASH 制造商:cypress semiconductor corp 系列:GL-N 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:256Mb （32M x 8，16M x 16） 寫周期時間 - 字，頁:100ns 訪問時間:100ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:56-TFSOP（0.724"，18.40mm 寬） 供應商器件封裝:56-TSOP 標準包裝:91
S29GL256N11FAI010 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 256M-Bit 32M x 8/16M x 16 110ns 64-Pin Fortified BGA Tray
S29GL256N11FAIIH2 制造商:Spansion 功能描述:S29GL256N11FAIIH2 - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*