參數資料
型號： S29GL256N10FFI010
廠商： SPANSION LLC
元件分類： PROM
英文描述： MirrorBit Flash Family
中文描述： 16M X 16 FLASH 3V PROM, 100 ns, PBGA64
封裝： 13 X 11 MM, LEAD FREE, FBGA-64
文件頁數： 49/95頁
文件大?。?/td> 3781K
代理商： S29GL256N10FFI010
May 30, 2008 S29GL-N_00_B8
S29GL-N
53
Data
She e t
Figure 9.2 Program Operation
Note
See Table 9.1 on page 60 and Table 9.3 on page 62 for program command sequence.
9.6
Program Suspend/Program Resume Command Sequence
The Program Suspend command allows the system to interrupt a programming operation or a Write to Buffer
programming operation so that data can be read from any non-suspended sector. When the Program
Suspend command is written during a programming process, the device halts the program operation within
15 s maximum (5 s typical) and updates the status bits. Addresses are not required when writing the
Program Suspend command.
After the programming operation is suspended, the system can read array data from any non-suspended
sector. The Program Suspend command may also be issued during a programming operation while an erase
is suspended. In this case, data may be read from any addresses not in Erase Suspend or Program Suspend.
If a read is needed from the Secured Silicon Sector area (One-time Program area), then user must use the
proper command sequences to enter and exit this region. Note that the Secured Silicon Sector autoselect,
and CFI functions are unavailable when program operation is in progress.
The system may also write the autoselect command sequence when the device is in the Program Suspend
mode. The system can read as many autoselect codes as required. When the device exits the autoselect
mode, the device reverts to the Program Suspend mode, and is ready for another valid operation. See
After the Program Resume command is written, the device reverts to programming. The system can
determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard
program operation. See Write Operation Status on page 64 for more information.
The system must write the Program Resume command (address bits are don’t care) to exit the Program
Suspend mode and continue the programming operation. Further writes of the Resume command are
ignored. Another Program Suspend command can be written after the device has resume programming.
START
Write Program
Command Sequence
Data Poll
from System
Verify Data?
No
Yes
Last Address?
No
Yes
Programming
Completed
Increment Address
Embedded
Program
algorithm
in progress
相關PDF資料
PDF描述
S29GL256N80FAI010 MirrorBit Flash Family
S29GL256N80FFI010 MirrorBit Flash Family
S29GL256N80FFI013 MirrorBit Flash Family
S29JL032H90TAI223 2M X 16 FLASH 3V PROM, 90 ns, PDSO48
S29WS064N0PBAW011 256/128/64 MEGABIT CMOS 1.8 VOLT ONLY SIMULTANEOUS READ/WRITE BURST MODE FLASH MEMORY
相關代理商/技術參數
參數描述
S29GL256N10FFI012 制造商:Spansion 功能描述:Flash - NOR IC
S29GL256N10FFI020 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 256Mbit 32M/16M x 8bit/16bit 100ns 64-Pin Fortified BGA Tray 制造商:Spansion 功能描述:MIRRORBIT FLASH 256MB SMD 29LV256
S29GL256N10TFI010 功能描述:IC FLASH 制造商:cypress semiconductor corp 系列:GL-N 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:256Mb （32M x 8，16M x 16） 寫周期時間 - 字，頁:100ns 訪問時間:100ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:56-TFSOP（0.724"，18.40mm 寬） 供應商器件封裝:56-TSOP 標準包裝:91
S29GL256N11FAI010 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 256M-Bit 32M x 8/16M x 16 110ns 64-Pin Fortified BGA Tray
S29GL256N11FAIIH2 制造商:Spansion 功能描述:S29GL256N11FAIIH2 - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*