參數資料
型號： MC68HC916X1
廠商： Motorola, Inc.
英文描述： 16-Bit Modular Microcontroller(16位模塊化微控制器)
中文描述： 16位微控制器模塊（16位模塊化微控制器）
文件頁數： 47/172頁
文件大?。?/td> 1035K
代理商： MC68HC916X1
MC68HC916X1
MC68HC916X1TS/D
MOTOROLA
47
The bits in this register control the direction of the pin drivers when the pins are configured as I/O.
Any bit in this register set to one configures the corresponding pin as an output. Any bit in this reg-
ister cleared to zero configures the corresponding pin as an input. This register can be read or writ-
ten at any time the MCU is not in emulator mode.
The bits in PEPAR control the function of each port E pin. Any bit set to one defines the correspond-
ing pin to be a bus control signal, with the function shown in
Table 32
. Any bit cleared to zero de-
fines the corresponding pin to be an I/O pin, controlled by PORTE and DDRE.
BERR and DATA8 control the state of this register following reset. If BERR and/or DATA8 are low
during reset, this register is set to $00, defining all port E pins as I/O pins. If BERR and DATA8 are
both high during reset, the register is set to $FF, which defines all port E pins as bus control signals.
3.10.3 Port F
Port F pins can be configured as interrupt request inputs, edge-detect input/outputs, or discrete in-
put/outputs. When port F pins are configured for edge detection, and a priority level is specified by
writing a value to the port F edge-detect interrupt level register (PFLVR), port F control logic gener-
ates an interrupt request when the specified edge is detected. Interrupt vector assignment is made
by writing a value to the port F edge-detect interrupt vector register (PFIVR). The edge-detect inter-
rupt has the lowest arbitration priority in the SCIM.
A write to the port F data register is stored in the internal data latch, and if any port F pin is config-
ured as an output, the value stored for that bit is driven on the pin. A read of PORTF returns the
value on a pin only if the pin is configured as a discrete input. Otherwise, the value read is the value
stored in the data register.
1. Reserved
PEPAR
— Port E Pin Assignment
$YFFA17
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
PEPA7
PEPA6
PEPA5
PEPA4
RESERVED
PEPA1
RSVD
1
RESET:
8- AND 16-BIT EXPANDED MODES
DATA8
DATA8
DATA8
DATA8
DATA8
DATA8
DATA8
DATA8
SINGLE-CHIP MODE
0
0
0
0
0
0
0
0
Table 32 Port E Pin Assignments
PEPAR Bit
PEPA7
PEPA6
PEPA5
PEPA4
PEPA1
Port E Signal
PE7
PE6
PE5
PE4
PE1
Bus Control Signal
SIZ1
SIZ0
AS
DS
DSACK1
PORTF0, PORTF1
— Port F Data Register
$YFFA19, YFFA1B
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
NOT USED
PF7
PF6
RESERVED
PF0
RESET:
U
U
U
U
U
U
U
U
相關PDF資料
PDF描述
MC68HC9D60 Advance Information - Rev 4.0
MC68HC12D60 Advance Information - Rev 4.0
MC68HCL05C8A 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HSC05C8A 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HCP11 8-Bit Microcontrollers
相關代理商/技術參數
參數描述
MC68HC98LJ12CFU 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述:
MC68HC98LJ12CFUE 功能描述:8位微控制器 -MCU 8 BIT MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC9S08RC60 L33R DIE 制造商:Motorola Inc 功能描述:
MC68HCP11A1CFN3 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HCP11A1FN 制造商:MOTORALA 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*