參數資料
型號： MC68HC916X1
廠商： Motorola, Inc.
英文描述： 16-Bit Modular Microcontroller(16位模塊化微控制器)
中文描述： 16位微控制器模塊（16位模塊化微控制器）
文件頁數： 107/172頁
文件大?。?/td> 1035K
代理商： MC68HC916X1
MC68HC916X1
MC68HC916X1TS/D
MOTOROLA
107
7.4.2 QSPI Registers
The programmer's model for the QSPI submodule consists of the QSM global and pin control reg-
isters, four QSPI control registers, one status register, and the 80-byte QSPI RAM.
The CPU can read and write to registers and RAM. The four control registers must be initialized
before the QSPI is enabled to ensure defined operation. SPCR1 should be written last because it
contains QSPI enable bit SPE. Asserting this bit starts the QSPI. The QSPI control registers are
reset to a defined state and can then be changed by the CPU. Reset values are shown below each
register.
Table 58
shows a memory map of the QSPI.
Writing a different value into any control register except SPCR2 while the QSPI is enabled disrupts
operation. SPCR2 is buffered to prevent disruption of the current serial transfer. After completion of
the current serial transfer, the new SPCR2 values become effective.
Writing the same value into any control register except SPCR2 while the QSPI is enabled has no
effect on QSPI operation. Rewriting NEWQP[3:0] in SPCR2 causes execution to restart at the des-
ignated location.
Table 57 QSPI Pins
Pin Name(s)
Master In Slave Out
Mnemonic(s)
MISO
Mode
Master
Slave
Master
Slave
Master
Slave
Master
Master
Master
Slave
Function
Serial Data Input to QSPI
Serial Data Output from QSPI
Serial Data Output from QSPI
Serial Data Input to QSPI
Clock Output from QSPI
Clock Input to QSPI
Select Peripherals
Selects Peripheral
Causes mode fault
Initiates Serial Transfer
Master Out Slave In
MOSI
Serial Clock
SCK
Peripheral Chip Selects
Peripheral Chip Select
Slave Select
PCS[3:1]
PCS0
SS
Table 58 QSPI Memory Map
Address
$YFFC18
$YFFC1A
$YFFC1C
$YFFC1E
$YFFC1F
$YFFD00
$YFFD20
$YFFD40
Name
SPCR0
SPCR1
SPCR2
SPCR3
SPSR
RR[0:F]
TR[0:F]
CR[0:F]
Usage
QSPI Control Register 0
QSPI Control Register 1
QSPI Control Register 2
QSPI Control Register 3
QSPI Status Register
QSPI Receive Data (16 Words)
QSPI Transmit Data (16 Words)
QSPI Command Control (8 Words)
相關PDF資料
PDF描述
MC68HC9D60 Advance Information - Rev 4.0
MC68HC12D60 Advance Information - Rev 4.0
MC68HCL05C8A 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HSC05C8A 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HCP11 8-Bit Microcontrollers
相關代理商/技術參數
參數描述
MC68HC98LJ12CFU 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述:
MC68HC98LJ12CFUE 功能描述:8位微控制器 -MCU 8 BIT MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC9S08RC60 L33R DIE 制造商:Motorola Inc 功能描述:
MC68HCP11A1CFN3 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HCP11A1FN 制造商:MOTORALA 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*