- 您現在的位置：買賣IC網 > PDF目錄180233 > M58WR064HU70ZB6U 4M X 16 FLASH 1.8V PROM, 70 ns, PBGA44 PDF資料下載
參數資料
| 型號： | M58WR064HU70ZB6U |
| 元件分類： | PROM |
| 英文描述： | 4M X 16 FLASH 1.8V PROM, 70 ns, PBGA44 |
| 封裝： | 7.70 X 9 MM, 0.50 MM PITCH, ROHS COMPLIANT, VFBGA-44 |
| 文件頁數： | 45/117頁 |
| 文件大?。?/td> | 2300K |
| 代理商： | M58WR064HU70ZB6U |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁當前第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁
M58WR064HU M58WR064HL
Command interface - Factory program commands
33/117
6.3.2
Program Phase
The Program Phase requires n+1 cycles, where n is the number of Words (refer to Table 7:
Three successive steps are required to issue and execute the Program Phase of the
command.
1.
Use one Bus Write operation to latch the Start Address and the first Word to be
programmed. The Status Register Bank Write Status bit SR0 should be read to check
that the P/E.C. is ready for the next Word.
2.
Each subsequent Word to be programmed is latched with a new Bus Write operation.
The address can either remain the Start Address, in which case the P/E.C. increments
the address location or the address can be incremented in which case the P/E.C.
jumps to the new address. If any address that is not in the same block as the Start
Address is given with data FFFFh, the Program Phase terminates and the Verify Phase
begins. The Status Register bit SR0 should be read between each Bus Write cycle to
check that the P/E.C. is ready for the next Word.
3.
Finally, after all Words have been programmed, write one Bus Write operation with data
FFFFh to any address outside the block containing the Start Address, to terminate the
programming phase. If the data is not FFFFh, the command is ignored.
The memory is now set to enter the Verify Phase.
6.3.3
Verify Phase
The Verify Phase is similar to the Program Phase in that all Words must be resent to the
memory for them to be checked against the programmed data. The Program/Erase
Controller checks the stream of data with the data that was programmed in the Program
Phase and reprograms the memory location if necessary.
Three successive steps are required to execute the Verify Phase of the command.
1.
Use one Bus Write operation to latch the Start Address and the first Word, to be
verified. The Status Register bit SR0 should be read to check that the Program/Erase
Controller is ready for the next Word.
2.
Each subsequent Word to be verified is latched with a new Bus Write operation. The
Words must be written in the same order as in the Program Phase. The address can
remain the Start Address or be incremented. If any address that is not in the same
block as the Start Address is given with data FFFFh, the Verify Phase terminates.
Status Register bit SR0 should be read to check that the P/E.C. is ready for the next
Word.
3.
Finally, after all Words have been verified, write one Bus Write operation with data
FFFFh to any address outside the block containing the Start Address, to terminate the
Verify Phase.
If the Verify Phase is successfully completed the memory remains in Read Status Register
mode. If the Program/Erase Controller fails to reprogram a given location, the error will be
signaled in the Status Register.
6.3.4
Exit Phase
Status Register P/E.C. bit SR7 set to ‘1’ indicates that the device has returned to Read
mode. A full Status Register check should be done to ensure that the block has been
successfully programmed. See the section on the Status Register for more details.
相關PDF資料 |
PDF描述 |
|---|---|
| M59DR032F100N1T | 2M X 16 FLASH 1.8V PROM, 100 ns, PDSO48 |
| M5F7924 | 24 V FIXED NEGATIVE REGULATOR, PSFM3 |
| M5F7920 | 20 V FIXED NEGATIVE REGULATOR, PSFM3 |
| M5F7918 | 18 V FIXED NEGATIVE REGULATOR, PSFM3 |
| M5F7915 | 15 V FIXED NEGATIVE REGULATOR, PSFM3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M58WR064KB70ZB6E | 制造商:Micron Technology Inc 功能描述:WIRELESS FLASH VFBGA 7.7X9.0X1.0 56 8X7 0.75 - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 64MBIT 70NS 56VFBGA |
| M58WR064KB70ZB6F | 制造商:Micron Technology Inc 功能描述:FLASH 28F640W18TD 60 VF-PBGA56 SB48 EX - Tape and Reel |
| M58WR064KB70ZB6F TR | 制造商:Micron Technology Inc 功能描述:IC FLASH 64MBIT 70NS 56VFBGA |
| M58WR064KB7AZB6E | 制造商:Micron Technology Inc 功能描述:WIRELESS - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 64MBIT 70NS 56VFBGA |
| M58WR064KB7AZB6F | 制造商:Micron Technology Inc 功能描述:WIRELESS - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。