- 您現在的位置：買賣IC網 > PDF目錄180233 > M58WR064HU70ZB6U 4M X 16 FLASH 1.8V PROM, 70 ns, PBGA44 PDF資料下載
參數資料
| 型號： | M58WR064HU70ZB6U |
| 元件分類： | PROM |
| 英文描述： | 4M X 16 FLASH 1.8V PROM, 70 ns, PBGA44 |
| 封裝： | 7.70 X 9 MM, 0.50 MM PITCH, ROHS COMPLIANT, VFBGA-44 |
| 文件頁數： | 44/117頁 |
| 文件大?。?/td> | 2300K |
| 代理商： | M58WR064HU70ZB6U |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁
Command interface - Factory program commands
M58WR064HU M58WR064HL
32/117
6.3
Enhanced Factory Program command
The Enhanced Factory Program command can be used to program large streams of data
within any one block. It greatly reduces the total programming time when a large number of
Words are written to a block at any one time.
If the block being programmed is protected then the Program operation will abort, the data
in the block will not be changed and the Status Register will output the error.
The use of the Enhanced Factory Program command requires certain operating conditions.
VPP must be set to VPPH
VDD must be within operating range
Ambient temperature TA must be 30 °C ± 10°C
The targeted block must be unlocked
Dual operations are not supported during the Enhanced Factory Program operation and the
command cannot be suspended.
For optimum performance the Enhanced Factory Program commands should be limited to a
maximum of 100 program/erase cycles per block. If this limit is exceeded the internal
algorithm will continue to work properly but some degradation in performance is possible.
Typical Program times are given in Table 16.
The Enhanced Factory Program command has four phases: the Setup Phase, the Program
Phase to program the data to the memory, the Verify Phase to check that the data has been
correctly programmed and reprogram if necessary and the Exit Phase. Refer to Table 7:
6.3.1
Setup Phase
The Enhanced Factory Program command requires two Bus Write operations to initiate the
command.
The first bus cycle sets up the Enhanced Factory Program command.
The second bus cycle confirms the command.
The Status Register P/E.C. Bit SR7 should be read to check that the P/E.C. is ready. After
the confirm command is issued, read operations output the Status Register data. The read
Status Register command must not be issued as it will be interpreted as data to program.
If the second bus cycle is not EFP confirm(D0h), the Status Register bits SR4 and SR5 are
set and the command will be aborted.
VPP value must be in the VPPH range during the Confirm command, otherwise SR4 and SR3
will be set and the command will be aborted.
相關PDF資料 |
PDF描述 |
|---|---|
| M59DR032F100N1T | 2M X 16 FLASH 1.8V PROM, 100 ns, PDSO48 |
| M5F7924 | 24 V FIXED NEGATIVE REGULATOR, PSFM3 |
| M5F7920 | 20 V FIXED NEGATIVE REGULATOR, PSFM3 |
| M5F7918 | 18 V FIXED NEGATIVE REGULATOR, PSFM3 |
| M5F7915 | 15 V FIXED NEGATIVE REGULATOR, PSFM3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M58WR064KB70ZB6E | 制造商:Micron Technology Inc 功能描述:WIRELESS FLASH VFBGA 7.7X9.0X1.0 56 8X7 0.75 - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 64MBIT 70NS 56VFBGA |
| M58WR064KB70ZB6F | 制造商:Micron Technology Inc 功能描述:FLASH 28F640W18TD 60 VF-PBGA56 SB48 EX - Tape and Reel |
| M58WR064KB70ZB6F TR | 制造商:Micron Technology Inc 功能描述:IC FLASH 64MBIT 70NS 56VFBGA |
| M58WR064KB7AZB6E | 制造商:Micron Technology Inc 功能描述:WIRELESS - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 64MBIT 70NS 56VFBGA |
| M58WR064KB7AZB6F | 制造商:Micron Technology Inc 功能描述:WIRELESS - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。