參數資料
型號： M38047M8-XXXFP
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述： 單芯片8位CMOS微機
文件頁數： 83/135頁
文件大?。?/td> 2055K
代理商： M38047M8-XXXFP
83
3803/3804 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
(2) START condition generating procedure using multi-master
1. Procedure example (The necessary conditions of the generat-
ing procedure are described as the following 2 to 5.
:
LDA
—
(Taking out of slave address value)
SEI
(Interrupt disabled)
BBS 5, S1, BUSBUSY (BB flag confirming and branch process)
BUSFREE:
STA S0
(Writing of slave address value)
LDM #$F0, S1
(Trigger of START condition generating)
CLI
(Interrupt enabled)
:
BUSBUSY:
CLI
(Interrupt enabled)
:
2. Use
“
Branch on Bit Set
”
of
“
BBS 5, $0014,
–”
for the BB flag
confirming and branch process.
3. Use
“
STA $12, STX $12
”
or
“
STY $12
”
of the zero page ad-
dressing instruction for writing the slave address value to the
I
2
C data shift register.
4. Execute the branch instruction of above 2 and the store instruc-
tion of above 3 continuously shown the above procedure
example.
5. Disable interrupts during the following three process steps:
BB flag confirming
Writing of slave address value
Trigger of START condition generating
When the condition of the BB flag is bus busy, enable interrupts
immediately.
(3) RESTART condition generating procedure
1. Procedure example (The necessary conditions of the generat-
ing procedure are described as the following 2 to 4.)
Execute the following procedure when the PIN bit is
“
0.
”
:
LDM #$00, S1
(Select slave receive mode)
LDA
—
(Taking out of slave address value)
SEI
(Interrupt disabled)
STA S0
(Writing of slave address value)
LDM #$F0, S1
(
Trigger of RESTART condition generating
)
CLI
(Interrupt enabled)
:
2. Select the slave receive mode when the PIN bit is
“
0.
”
Do not
write
“
1
”
to the PIN bit. Neither
“
0
”
nor
“
1
”
is specified for the
writing to the BB bit.
The TRX bit becomes
“
0
”
and the SDA pin is released.
3. The SCL pin is released by writing the slave address value to
the I
2
C data shift register.
4. Disable interrupts during the following two process steps:
Writing of slave address value
Trigger of RESTART condition generating
(4) Writing to I
2
C status register
Do not execute an instruction to set the PIN bit to
“
1
”
from
“
0
”
and
an instruction to set the MST and TRX bits to
“
0
”
from
“
1
”
simulta-
neously. It is because it may enter the state that the SCL pin is
released and the SDA pin is released after about one machine
cycle. Do not execute an instruction to set the MST and TRX bits
to
“
0
”
from
“
1
”
simultaneously when the PIN bit is
“
1.
”
It is because
it may become the same as above.
(5) Process of after STOP condition generating
Do not write data in the I
2
C data shift register S0 and the I
2
C sta-
tus register S1 until the bus busy flag BB becomes
“
0
”
after
generating the STOP condition in the master mode. It is because
the STOP condition waveform might not be normally generated.
Reading to the above registers does not have the problem.
I
Precautions when using multi-master I
2
C-
BUS interface
(1) Read-modify-write instruction
The precautions when the read-modify-write instruction such as
SEB, CLB etc. is executed for each register of the multi-master
I
2
C-BUS interface are described below.
I
2
C data shift register (S0: address 0011
16
)
When executing the read-modify-write instruction for this regis-
ter during transfer, data may become a value not intended.
I
2
C slave address registers 0 to 2 (S0D0 to S0D2: addresses
0FF7
16
to0FF9
16
)
When the read-modify-write instruction is executed for this regis-
ter at detecting the STOP condition, data may become a value
not intended. It is because H/W changes the read/write bit
(RWB) at the above timing.
I
2
C status register (S1: address 0013
16
)
Do not execute the read-modify-write instruction for this register
because all bits of this register are changed by H/W.
I
2
C control register (S1D: address 0014
16
)
When the read-modify-write instruction is executed for this regis-
ter at detecting the START condition or at completing the byte
transfer, data may become a value not intended. Because H/W
changes the bit counter (BC0-BC2) at the above timing.
I
2
C clock control register (S2: address 0015
16
)
The read-modify-write instruction can be executed for this regis-
ter.
I
2
C START/STOP condition control register (S2D: address
0016
16
)
The read-modify-write instruction can be executed for this regis-
ter.
相關PDF資料
PDF描述
M38037M8-XXXHP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38037M8-XXXSP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M3803 Single Chip 8 Bits Microcomputer(8位單片機)
M3804 Single Chip 8 Bits Microcomputer(8位單片機)
M38034 SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M38049FFFP#U0 制造商:Renesas Electronics Corporation 功能描述:
M38049FFLHP#U0 制造商:Renesas Electronics Corporation 功能描述:
M38049RLSS 功能描述:DEV EMULATOR CHIP RAM 2KB 64SDIP RoHS:否 類別:編程器，開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:*
M3806 功能描述:電纜固定件和配件 LTSCG 625 BLACK RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度:
M3806 BK001 制造商:Alpha Wire Company 功能描述:CBL 8COND 18AWG BLK 1000'
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*