參數資料
型號: M37733MHB
廠商: Mitsubishi Electric Corporation
英文描述: Single Chip 16 Bits CMOS Microcomputer(16位單片機)
中文描述: 單片微機16位的CMOS(16位單片機)
文件頁數: 9/89頁
文件大?。?/td> 1992K
代理商: M37733MHB
9
MITSUBISHI MICROCOMPUTERS
M37733MHBXXXFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
7. Overflow flag (V)
The overflow flag is effective only when addition or subtraction is
performed with treating a word as a signed binary number. When the
data length flag (m) is “0”, the overflow flag is set if the result of
addition or subtraction is outside the range between – 32768 and
+32767. When the data length flag (m) is “1”, the overflow flag is set
if the result of addition or subtraction is outside the range between
–128 and +127. It is reset in the other cases. The overflow flag can
also be set or reset directly with the SEP or CLV, CLP instructions.
8. Negative flag (N)
The negative flag is set when the result of arithmetic operation or
data transfer is negative (If data length flag (m) is “0”, data bit 15 is
“1”. If data length flag (m) is “1”, data bit 7 is “1”.) It is reset in the
other cases. It can also be set or reset with the SEP or CLP
instructions.
9. Processor interrupt priority level (IPL)
The processor interrupt priority level (IPL) consists of 3 bits and
determines the processor interrupt priority level (0 to 7). Interrupt is
enabled when the interrupt priority level of the device requesting
interrupt (the priority can be set using the interrupt control register) is
higher than the processor interrupt priority level. When interrupt is
enabled, the current processor interrupt priority level is saved in a
stack and the processor interrupt priority level is replaced by the
interrupt priority level of the device requesting the interrupt. Refer to
the section on interrupts for more details.
BUS INTERFACE UNIT
The CPU operates on an internal clock
’s frequency is twice the bus cycle frequency. In order to speed up
processing, a bus interface unit is used to pre-fetch instructions when
the data bus is idle. The bus interface unit synchronizes the CPU
and the bus and pre-fetches instructions. Figure 4 shows the
relationship between the CPU and the bus interface unit. The bus
interface unit has a program address register, a 3-byte instruction
queue buffer, a data address register, and a 2-byte data buffer.
The bus interface unit obtains an instruction code from the memory
and stores it in the instruction queue buffer, obtains data from the
memory and stores it in the data buffer, or writes the data from the
data buffer to the memory.
’s frequency. Internal clock
Fig. 4 Relationship between the CPU and the bus interface unit
CPU
Bus interface
unit
E
ALE
BYTE
HOLD
BHE
R/
W
D
15
– D
8
A
23
– A
0
D
7
– D
0
D'
15 –
D'
8
Control signal
D'
7 –
D'
0
A'
23 –
A'
0
相關PDF資料
PDF描述
M37735S4L Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37736MHL Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M3773S4B Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M3773S4L Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37751 16-Bit Single-Chip Microcomputer(16位單片微控制器)
相關代理商/技術參數
參數描述
M37733MHB-217FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37733MHB-226FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37733MHB242FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37733MHB274FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37733MHBXXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER