- 您現在的位置：買賣IC網 > PDF目錄384636 > M37733MHB (Mitsubishi Electric Corporation) Single Chip 16 Bits CMOS Microcomputer(16位單片機) PDF資料下載
參數資料
| 型號： | M37733MHB |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| 中文描述： | 單片微機16位的CMOS（16位單片機） |
| 文件頁數： | 46/89頁 |
| 文件大?。?/td> | 1992K |
| 代理商： | M37733MHB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁
46
MITSUBISHI MICROCOMPUTERS
M37733MHBXXXFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
INPUT / OUTPUT PINS
Ports P0 to P8 all have a port direction register and each bit can be
programmed for input or output. A pin becomes an output pin when
the corresponding bit of the port direction register is set to “1” and an
input pin when the bit is cleared to “0”.
When a pin is programmed for output, the data is written to the port
latch and is output, and the contents of the port latch is read instead
of the value of the pin. Therefore, a previously output value can be
read correctly even when the output “L” voltage is raised by directly
driving an LED or others.
A pin programmed for input is floating and the value input to the pin
can be read. When a pin is programmed for input, the data is written
only in the port latch and the pin retains floating.
Ports P5
4
to P5
7
, and P6
2
– P6
4
, however, have pull-up transistors
and the port’s pull-up function can be selected by setting “1” to bits 6,
5, 3 of the port function control register (reffer to Figure 11.) A port
which corresponds to a port direction register’s bit set to “0” is pulled
up. A port which corresponds to a bit set to “1” is an output pin and it
is not pulled up.
Figures 55 and 56 show the block diagram of ports P0 to P8 and the
E
pin output format.
In the memory expansion mode and the microprocessor mode, ports
P0 to P4 are also used as address, data, and control signal pins.
Refer to the section on the processor modes for more details.
Figure 54 shows an example of a reset circuit. If the stabilized clock
is input from the external to the main-clock oscillation circuit, the reset
input voltage must be 0.9 V or less when the power source voltage
reaches 4.5 V. If a resonator/oscillator is connected to the main-clock
oscillation circuit, change the reset input voltage from “L” to “H” after
the main-clock oscillation is fully stabilized.
V
CC
RESET
RESET
V
CC
0V
0V
4.5V
0.9V
Power on
Note.
In this case, stabilized clock is input from the
external to the main-clock oscillation circuit.
Perform careful evaluation at the system design
level before using.
Fig. 54 Example of a reset circuit
相關PDF資料 |
PDF描述 |
|---|---|
| M37735S4L | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37736MHL | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M3773S4B | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M3773S4L | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37751 | 16-Bit Single-Chip Microcomputer(16位單片微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37733MHB-217FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37733MHB-226FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37733MHB242FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37733MHB274FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37733MHBXXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。