參數資料
型號: M37733MHB
廠商: Mitsubishi Electric Corporation
英文描述: Single Chip 16 Bits CMOS Microcomputer(16位單片機)
中文描述: 單片微機16位的CMOS(16位單片機)
文件頁數: 43/89頁
文件大?。?/td> 1992K
代理商: M37733MHB
43
MITSUBISHI MICROCOMPUTERS
M37733MHBXXXFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
(3) Single sweep mode
Single sweep mode is selected when bit 3 of A-D control register 0 is
“0” and bit 4 is “1”.
In the single sweep mode, the number of analog input pins to be
swept can be selected. Analog input pins are selected by bits 1 and
0 of the A-D control register 1 (address 1F
16
). Two pins, four pins, six
pins or eight pins can be selected as analog input pins, depending
on the contents of these bits.
A-D conversion is performed only for selected input pins. After A-D
conversion is performed for input of AN
0
pin, the conversion result is
stored in A-D register 0, and in the same way, A-D conversion is
performed for selected pins one after another. After A-D conversion
is performed for all selected pins, the sweep is stopped.
A-D conversion can be started with a software trigger or with an
external trigger input. A software trigger is selected when bit 5 is “0”
and an external trigger is selected when it is “1”.
When a software trigger is selected, A-D conversion is started when
A-D control register 0 bit 6 (A-D conversion start flag) is set to “1”.
When A-D conversion of all selected pins ends, an interrupt request
bit of the A-D conversion interrupt control register is set to “1”. At the
same time, A-D conversion start flag is cleared and A-D conversion
stops.
If an external trigger is selected, A-D conversion starts when the A-D
conversion start flag is “1” and the
AD
TRG
input changes from “H” to
“L”. In this case, the A-D conversion result which is stored in the A-D
register 5 becomes invalid because the
AD
TRG
pin is also used as the
AN
5
pin.
The operation by external trigger is the same as that done by software
trigger except that the A-D conversion start flag is not cleared after
A-D conversion and a retrigger can be available during A-D
conversion.
(4) Repeat sweep mode
Repeat sweep mode 0 is selected when bit 3 of A-D control register
0 is “1” and bit 4 is “1”.
The difference from the single sweep mode is that A-D conversion
does not stop after converting from the AN
0
pin to the selected pins,
but repeats again from the AN
0
pin. The repeat is performed among
the selected pins. Also, no interrupt request is generated. Furthermore,
if software trigger is selected, the A-D conversion start flag is not
cleared. The A-D register can be read at any time.
相關PDF資料
PDF描述
M37735S4L Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37736MHL Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M3773S4B Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M3773S4L Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37751 16-Bit Single-Chip Microcomputer(16位單片微控制器)
相關代理商/技術參數
參數描述
M37733MHB-217FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37733MHB-226FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37733MHB242FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37733MHB274FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37733MHBXXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER