參數資料
型號: M37733MHB
廠商: Mitsubishi Electric Corporation
英文描述: Single Chip 16 Bits CMOS Microcomputer(16位單片機)
中文描述: 單片微機16位的CMOS(16位單片機)
文件頁數: 56/89頁
文件大?。?/td> 1992K
代理商: M37733MHB
56
MITSUBISHI MICROCOMPUTERS
M37733MHBXXXFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
Oscillation circuit control register 0
X
drivability selection bit
0 : LOW
1 : HIGH
Main clock stop bit
0 : Main-clock oscillation is available.
1 : Main-clock oscillation is stopped.
System clock selection bit
Port-X
C
selection bit = “0” (Sub clock is not used.)
0 : Main clock is selected.
1 : Main clock divided by 8 is selected.
Port-X
selection bit = “1” (Sub clock is used.)
0 : Main clock is selected.
1 : Sub clock is selected.
Port-Xc selection bit
0 : Ports P7
7
and P7
6
are selected. (Sub clock is not used.)
1 : Pins X
CIN
and X
COUT
are selected. (Sub clock is used.)
System clock stop bit at wait state
0 : Clocks f
2
to f
512
are operating at WIT state
1 : Clocks f
2
to f
512
stop at WIT state
Signal output disable selection bit (Refer to Table 7.)
Address
6C
16
Note.
Write to the oscillation circuit control
register 1 as the flow shown in Figure 64.
CM
6
CM
5
CM
4
CM
3
CM
2
CM
0
7
6
5
4
3
2
1
0
Main clock division selection bit
0 : Main clock is divided by 2.
1 : Main clock is not divided by 2.
Main clock external input selection bit
0 : Main-clock oscillation circuit is operating by itself.
Watchdog timer is used at returning from STP state.
1 : Main-clock is input externally.
Watchdog timer is not used at returning from STP state.
Sub clock external input selection bit
0 : Sub-clock oscillation circuit is operating by itself.
Port P7
functions as X
pin.
Watchdog timer is used at returning from STP state.
1 : Sub-clock is input externally.
Port P7
6
functions as I/O port.
Watchdog timer is not used ar returning from STP state.
X : Not used
0 : Always “0” (However, writing data “55
16
” shown in Figure 64 is possible.)
Clock prescaler reset bit
Address
6F
16
CC
0
CC
1
CC
2
0
7
6
5
4
3
2
1
0
Fig. 63 Bit configuration of oscillation circuit control registers 0, 1
Fig. 64 How to write data in oscillation circuit control register 1
Writing data “80
16
” (LDM instruction)
Reset clock prescaler
Writing data “55
16
” (LDM instruction)
Writing data “0Y
16
” (LDM instruction)
CC
2
to CC
0
selection bits
How to reset clock prescaler
How to write in CC
2
to CC
0
selection bits
Note.
“Y” is the sum of bits to be set. For example,
when
setting bits 2 and 1 to “1”, “Y” becomes “6”.
Next instruction
相關PDF資料
PDF描述
M37735S4L Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37736MHL Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M3773S4B Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M3773S4L Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37751 16-Bit Single-Chip Microcomputer(16位單片微控制器)
相關代理商/技術參數
參數描述
M37733MHB-217FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37733MHB-226FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37733MHB242FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37733MHB274FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37733MHBXXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER