- 您現在的位置：買賣IC網 > PDF目錄384636 > M37733MHB (Mitsubishi Electric Corporation) Single Chip 16 Bits CMOS Microcomputer(16位單片機) PDF資料下載
參數資料
| 型號： | M37733MHB |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| 中文描述： | 單片微機16位的CMOS（16位單片機） |
| 文件頁數： | 62/89頁 |
| 文件大?。?/td> | 1992K |
| 代理商： | M37733MHB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁當前第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁
62
MITSUBISHI MICROCOMPUTERS
M37733MHBXXXFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
The wait/stop state is terminated by interrupt acceptance or reset.
Accordingly, it is necessary to prepare the state in which any interrupt
can be accepted before the WIT/STP instruction is executed.
Additionally, it is necessary to set the system clock stop bit at wait
state before the WIT instruction is executed.
When the WIT/STP instruction is executed in a bus access cycle, the
bus enters the non-access state (
E
is at “H”) because internal clock
φ
(or oscillation) is stopped after the read/write in this cycle is finished.
Pins P0
0
/A
0
to P3
3
/
HLDA
normally retain the state at which internal
clock
φ
is stopped in the wait/stop state.
However, only in the memory expansion mode and the microprocessor
mode, arbitrary data which is set in the port P0 to P3 latches can be
output from pins P0
0
/A
0
to P3
3
/
HLDA
even at the wait/stop state when
the following conditions are satisfied before the WIT/STP instruction
execution.
The standby state selection bit (bit 0 of the port function control
register) is set to “1”.
“FF
16
” is set into the port P0 to P3 direction registers.
Furthermore, when the standby state selection bit is set to “1” and bit
6 of the oscillation circuit control register 0 (signal output disable
selection bit) is set to “1”, “L” level can be output from the
E
pin at the
wait/stop state. For the signal output disable selection bit, refer to
Table 7 on the processor mode section.
Note that the function of arbitrary data output cannot be emulated
using a debugger.
相關PDF資料 |
PDF描述 |
|---|---|
| M37735S4L | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37736MHL | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M3773S4B | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M3773S4L | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37751 | 16-Bit Single-Chip Microcomputer(16位單片微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37733MHB-217FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37733MHB-226FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37733MHB242FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37733MHB274FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37733MHBXXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。