參數資料
型號： LU3X31FT
廠商： Lineage Power
英文描述： Single-Port 3 V 10/100 Ethernet Transceiver TX/FX(單端口 3 V 10M位和100M位以太網收發器)
中文描述： 單端口3伏10/100以太網收發器德克薩斯州/外匯（單端口3伏1000萬位和100米位以太網收發器）
文件頁數： 16/50頁
文件大?。?/td> 633K
代理商： LU3X31FT
LU3X31FT Single-Port 3 V
10/100 Ethernet Transceiver TX/FX
Preliminary Data Sheet
July 2000
16
Lucent Technologies Inc.
Functional Description
(continued)
Upon detection of sufficient IDLE symbols within the
722
μ
s period, the hold timer will reset and begin a new
countdown. This monitoring operation will continue
indefinitely given a properly operating network connec-
tion with good signal integrity. If the link state monitor
does not recognize sufficient unscrambled IDLE sym-
bols within the 722
μ
s period, the entire descrambler
will be forced out of the current state of synchronization
and reset in order to reacquire synchronization. Regis-
ter 18h, bit 3, can be used to extend the timer to
2000
μ
s.
Symbol Alignment.
The symbol alignment circuit in
the LU3X31FT determines code word alignment by
recognizing the /J/K delimiter pair. This circuit operates
on unaligned 5-bit data from the descrambler and is
capable of finding /J/K at any of the five possible start-
ing positions within the descrambled data quints. Once
the /J/K symbol pair (11000 10001) is detected, subse-
quent data is aligned on a fixed boundary.
Symbol Decoding.
The symbol decoder functions as
a look-up table that translates incoming 5B symbols
into 4B nibbles. The symbol decoder first detects the
/J/K symbol pair preceded by IDLE symbols and
replaces the symbol with MAC preamble. All subse-
quent 5B symbols are converted to the corresponding
4B nibbles for the duration of the entire packet. This
conversion ceases upon the detection of the /T/R sym-
bol pair denoting the end of stream delimiter (ESD).
The translated data is presented on the RXD[3:0] sig-
nal lines with RXD[0] representing the least significant
bit of the translated nibble.
Valid Data Signal.
The valid data signal (RXDV) indi-
cates that recovered and decoded nibbles are being
presented on the RXD[3:0] outputs synchronous to
RXCLK. RXDV is asserted when the first nibble of
translated /J/K is ready for transfer over the media inde-
pendent interface (MII). It remains active until either the
/T/R delimiter is recognized, link test indicates failure,
or no signal is detected. On any of these conditions,
RXDV is deasserted.
Receiver Errors.
The RXER signal is used to commu-
nicate receiver error conditions. While the receiver is in
a state of holding RXDV asserted, the RXER will be
asserted for each code word that does not map to a
valid code-group.
100Base-X Link Monitor
The 100Base-X link monitor function allows the
receiver to ensure that reliable data is being received.
Without reliable data reception, the link monitor will halt
both transmit and receive operations until such time
that a valid link is detected.
The LU3X31FT performs the link integrity test as out-
lined in IEEE 100Base-X (Clause 24) link monitor state
diagram. The link status is multiplexed with 10 Mbits/s
link status to form the reportable link status bit in serial
management register 1, which is then driven to the
LNKLED pin.
When persistent signal energy is detected on the net-
work, the logic moves into a link-ready state after
approximately 500
μ
s, and waits for an enable from the
autonegotiation module. When received, the link-up
state is entered, and the transmit and receive logic
blocks become active. Should autonegotiation be dis-
abled, the link integrity logic moves immediately to the
link-up state after entering the link-ready state.
Carrier Sense.
Carrier sense (CRS) for 100 Mbits/s
operation is asserted upon the detection of two non-
contiguous zeros occurring within any 10-bit boundary
of the receive data stream.
The carrier sense function is independent of symbol
alignment. For 100 Mbits/s half-duplex operation, CRS
is asserted during either packet transmission or recep-
tion. For 100 Mbits/s full-duplex operation, CRS is
asserted only during packet reception. When the IDLE
symbol pair is detected in the receive data stream,
CRS is deasserted. In repeater mode, CRS is only
asserted due to receive activity.
Bad SSD Detection.
A bad start of stream delimiter
(Bad SSD) is an error condition that occurs in the
100Base-X receiver if carrier is detected (CRS
asserted) and a valid /J/K set of code groups (SSD) is
not received.
If this condition is detected, then the LU3X31FT will
assert RXER and present RXD[3:0] = 1110 to the MII
for the cycles that correspond to received 5B code-
groups until at least two IDLE code groups are
detected. In addition, the false carrier counter (address
13h) will be incremented by one. Once at least two
IDLE code groups are detected, RXER and CRS
become deasserted.
Far-End Fault Indication.
Autonegotiation provides a
mechanism for transferring information from the local
station to the link partner that a remote fault has
occurred for 100Base-TX. Since autonegotiation is not
相關PDF資料
PDF描述
LU3X32FT Two-Port 3 V 10/100 Ethernet Transceiver TX/FX(雙端口 3 V 10M位和100M位以太網收發器)
LU3X34FT Quad 3 V 10/100 Ethernet Transceiver TX/FX(四3 V 10/100以太網收發器)
LU3X51FT-J80 Single-Port 3V 10/100 Ethernet TransceiverTX/FX(單端口3V 10/100以太網收發器)
LU3X54FTL Quad-FET for 10Base-T/100Base-TX/FX(應用于10基數-T和100基數-TX/FX的四快速以太網收發器)
LU5X31F Gigabit Ethernet Transceiver(千兆位以太網收發器)
相關代理商/技術參數
參數描述
LU3X31T2T64 制造商:LUCENT 功能描述:NEW
LU3X31T-T64 制造商:AGERE 制造商全稱:AGERE 功能描述:LU3X31T-T64 Single-Port 3 10/100 Ethernet Transceiver TX
LU3X34FTR 制造商:AGERE 制造商全稱:AGERE 功能描述:Quad 3 V 10/100 Ethernet Transceiver TX/FX
LU3X34FTR-HS128-DB 制造商:AGERE 制造商全稱:AGERE 功能描述:Quad 3 V 10/100 Ethernet Transceiver TX/FX
LU3X54FT 制造商:AGERE 制造商全稱:AGERE 功能描述:QUAD-FET (Fast Ethernet Transceiver) for 10Base-T/100Base-TX/FX
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*