參數資料
型號： FDC37B787QF
廠商： SMSC Corporation
英文描述： Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
中文描述： 超級I / O與ACPI支持控制器，實時時鐘和消費性紅外
文件頁數： 144/249頁
文件大?。?/td> 932K
代理商： FDC37B787QF
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁當前第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁
BIT 0 - AL_REM_EN
One of the two control bits for the alarm wakeup
function; it is the “remember” enable bit for the
second alarm. This bit, if set to 1, wil cause the
system to power-up upon return of power if the
alarm 2 time has passed during loss of power. It is
only applicable when VTR=0. This bit is
independent of the other control bit for the alarm
wake-up function, AlE.
If AL_REM_EN is set and VTR=0 at the date/time
that the alarm is set for, the nPowerOn pin will go
active (low) and the machine will power-up as
soon as VTR comes back.
Bit 1 – VTR_POR_OFF
If VTR_POR_OFF is set, the nPowerOn pin will go
inactive (float) and the main power (Vcc) will
remain off when the VTR POR occurs. The
software must not set VTR_POR_OFF and
VTR_POR_EN at the same time.
BIT 2 - VTR_POR_EN
The enable bit for VTR POR. If VTR_POR_EN is
set, the nPowerOn pin will go active (low) and the
machine will power-up as soon as a VTR POR
occurs.
The
software
VTR_POR_OFF and VTR_POR_EN at the same
time.
Bits 3:6 - Reserved
Read as zero, ignore writes
Bit 7 - XTAL_CAP
This bit is used to specify the 32Khz XTAL load
capacitance (12pF vs. 6pF):
0=12pF, 1=6pF.
Registers 0Eh-7Ch, 7Fh in Bank 0 and 00h-7Fh
in Bank 1: General Purpose
Registers 0Eh-7Ch, 7Fh in Bank 0 and 00h-7Fh in
Bank 1 are general purpose CMOS registers.
These registers can be used by the host and are
fully available during the time update cycle. The
contents of these registers are preserved by the
battery power.
Interrupts
146
must
not
set
The RTC includes three separate fully- automatic
sources of interrupts to the processor. The alarm
interrupt may be programmed to occur at rates
from one-per-second to one-a-day. The periodic
interrupt may be selected for rates from
half-a-second to 122.070
μ
s. The update ended
interrupt may be used to indicate to the program
that an update cycle is completed. Each of
these independent interrupts are described in
greater detail in other sections.
The processor program selects which interrupts, if
any, it wishes to receive by writing a "1" to the
appropriate enable bits in Register B. A "0" in an
enable bit prohibits the IRQB port from being
asserted due to that interrupt cause. When an
interrupt event occurs a flag bit is set to a "1" in
Register C. Each of the three interrupt sources
have separate flag bits in Register C, which are
set independent of the state of the corresponding
enable bits in Register B. The flag bits may be
used with or without enabling the corresponding
enable bits. The flag bits in Register C are cleared
(record of the interrupt event is erased) when
Register C is read. Double latching is included in
Register C to ensure the bits that are set are
stable throughout the read cycle. All bits which
are high when read by the program are cleared,
and new interrupts are held until after the read
cycle. If an interrupt flag is already set when the
interrupt becomes enabled, the IRQB port is
immediately activated, though the interrupt
initiating the event may have occurred much
earlier.
When an interrupt flag bit is set and the
corresponding interrupt-enable bit is also set, the
IRQB port is driven low. IRQB is asserted as long
as at least one of the three interrupt sources has
its flag and enable bits both set. The IRQF bit in
Register C is a "1" whenever the IRQB port is
being driven low.
Frequency Divider
The RTC has 22 binary divider stages following
the clock input. The output of the divider is a 1 Hz
signal
to
the
logic. The divider is controlled by the three divider
bits (DV3-DV0) in Register A. As shown in Table
update-cycle
相關PDF資料
PDF描述
FDC37B78X Enhanced Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
FDC37B80X PC98/99 Compliant Enhanced Super I/O Controller with Keyboard/Mouse Wake-Up
FDC37C665IR 3/5 Volt Advanced High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controller with Infranred Support
FDC37C665GT High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
FDC37C666GT High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
相關代理商/技術參數
參數描述
FDC37B787QFP 功能描述:輸入/輸出控制器接口集成電路 Enhanced Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
FDC37B78X 制造商:SMSC 制造商全稱:SMSC 功能描述:Enhanced Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
FDC37B78X_07 制造商:SMSC 制造商全稱:SMSC 功能描述:Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
FDC37B802 制造商:Rochester Electronics LLC 功能描述:
FDC37B802QFP 制造商:Rochester Electronics LLC 功能描述:- Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*