參數資料
型號： FDC37B787QF
廠商： SMSC Corporation
英文描述： Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
中文描述： 超級I / O與ACPI支持控制器，實時時鐘和消費性紅外
文件頁數： 101/249頁
文件大?。?/td> 932K
代理商： FDC37B787QF
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁當前第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁
BIT 5 DIRECTION
If mode=000 or mode=010, this bit has no effect
and the direction is always out regardless of the
state of this bit. In all other modes, Direction is
valid and a logic 0 means that the printer port is in
output mode (write); a logic 1 means that the
printer port is in input mode (read).
BITS 6 and 7
during a read are a low level, and
cannot be written.
cFifo (Parallel Port Data FIFO)
ADDRESS OFFSET = 400h
Mode = 010
Bytes written or DMAed from the system to this
FIFO are transmitted by a hardware handshake to
the peripheral using the standard parallel port
protocol. Transfers to the FIFO are byte aligned.
This mode is only defined for the forward direction.
ecpDFifo (ECP Data FIFO)
ADDRESS OFFSET = 400H
Mode = 011
Bytes written or DMAed from the system to this
FIFO, when the direction bit is 0, are transmitted
by a hardware handshake to the peripheral using
the ECP parallel port protocol. Transfers to the
FIFO are byte aligned.
Data bytes from the peripheral are read under
automatic hardware handshake from ECP into this
FIFO when the direction bit is 1. Reads or DMAs
from the FIFO will return bytes of ECP data to the
system.
tFifo (Test FIFO Mode)
ADDRESS OFFSET = 400H
Mode = 110
Data bytes may be read, written or DMAed to or
from the system to this FIFO in any direction.
Data in the tFIFO will not be transmitted to the to
the parallel port lines using a hardware protocol
handshake. However, data in the tFIFO may be
displayed on the parallel port data lines.
The tFIFO will not stall when overwritten or
underrun. If an attempt is made to write data to a
full tFIFO, the new data is not accepted into the
101
tFIFO. If an attempt is made to read data from an
empty tFIFO, the last data byte is re-read again.
The full and empty bits must always keep track of
the correct FIFO state. The tFIFO will transfer data
at the maximum ISA rate so that software may
generate performance metrics.
The FIFO size and interrupt threshold can be
determined by writing bytes to the FIFO and
checking the full and serviceIntr bits.
The writeIntrThreshold can be determined by
starting with a full tFIFO, setting the direction bit to
0 and emptying it a byte at a time until serviceIntr
is set. This may generate a spurious interrupt, but
will indicate that the threshold has been reached.
The readIntrThreshold can be determined by
setting the direction bit to 1 and filling the empty
tFIFO a byte at a time until serviceIntr is set. This
may generate a spurious interrupt, but will indicate
that the threshold has been reached.
Data bytes are always read from the head of tFIFO
regardless of the value of the direction bit. For
example if 44h, 33h, 22h is written to the FIFO,
then reading the tFIFO will return 44h, 33h, 22h in
the same order as was written.
cnfgA (Configuration Register A)
ADDRESS OFFSET = 400H
Mode = 111
This register is a read only register. When read,
10H is returned. This indicates to the system that
this is an 8-bit implementation. (PWord = 1 byte)
cnfgB (Configuration Register B)
ADDRESS OFFSET = 401H
Mode = 111
BIT 7 compress
This bit is read only. During a read it is a low level.
This means that this chip does not support
hardware RLE compression. It does support
hardware de-compression!
BIT 6 intrValue
Returns the value on the ISA IRq line to determine
possible conflicts.
BITS [5:3] Parallel Port IRQ (read-only)
Refer to Table 44B.
相關PDF資料
PDF描述
FDC37B78X Enhanced Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
FDC37B80X PC98/99 Compliant Enhanced Super I/O Controller with Keyboard/Mouse Wake-Up
FDC37C665IR 3/5 Volt Advanced High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controller with Infranred Support
FDC37C665GT High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
FDC37C666GT High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
相關代理商/技術參數
參數描述
FDC37B787QFP 功能描述:輸入/輸出控制器接口集成電路 Enhanced Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
FDC37B78X 制造商:SMSC 制造商全稱:SMSC 功能描述:Enhanced Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
FDC37B78X_07 制造商:SMSC 制造商全稱:SMSC 功能描述:Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
FDC37B802 制造商:Rochester Electronics LLC 功能描述:
FDC37B802QFP 制造商:Rochester Electronics LLC 功能描述:- Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*