參數資料
型號： CN8223EPF
英文描述： ATM/SONET TRANSCEIVER|CMOS|QFP|160PIN|PLASTIC
中文描述： 的ATM / SONET的收發器|的CMOS | QFP封裝| 160PIN |塑料
文件頁數： 93/161頁
文件大?。?/td> 1865K
代理商： CN8223EPF
CN8223
3.0 Registers
ATM Transmitter/Receiver with UTOPIA Interface
3.3 Configuration Control Registers
100046D
Conexant
3-7
1
0
1
0
1
1
1
1
0x01
—
CONFIG_2 (Configuration Control Register 2)
The CONFIG_2 register is located at address 0x01 and controls transmit formatting and alarm generation.
Table 3-4
defines Alarm Controls for the Line Framing/PHY Formats.
Table 3-5
defines the control bits for
STS-1/STS-3c/STM-1.
Table 3-6
defines the overhead bits for Line Framing/PHY Formats.
Bit
Field
Size
Name
Description
15
1
Enable External
Overhead
Enables all overhead octets to be inserted externally in STS-1/STS-3c/STM-1 and
G.832 E3/E4 modes. If this bit is not set, internal generation of overhead octets is
enabled as described in
Section2.3
.
14
1
All-Zeros FEBE
Inserts an all-0s value in the FEBE field. The all-0s value provides an indication at
the far end that no BIP-8 errors are being detected. BIP-8 status and error counts
are not affected. This control bit is active in all modes whether the FEBE field is
single- or multi-bit.
13
1
All-1s FEBE
Inserts an all-1s value in the FEBE field of the transmit frame. The all-1s value
notifies the far end that the FEBE function is inhibited. BIP-8 status and error counts
are not affected. This control bit is active in all modes whether the FEBE field is
single- or multi-bit.
12
–
10
3
BIP Error Insert
Selects the BIP field that will be errored with the TXFEAC_ERRPAT register
according to the following:
These bits are cleared by the transmitter after the error is inserted in the overhead
field, and can be read as 0 to verify that error insertion has taken place.
9
–
4
6
Transmit Alarm
Control
Controls the generation of alarms for 57-octet PLCPs and internal framers. No
alarms are transmitted if all bits in this control field are set to 0. Setting any of these
bits to a 1 causes an alarm to be transmitted according to
Table3-4
and
Table3-5
.
For example, in STS-3c mode, setting bit 4 to a 1 will cause the Line AIS alarm to be
transmitted.
3
–
0
4
Overhead Control
Selectively disables overhead generation. Standard overhead is generated internally
if all bits in this control field are set to 0. Overhead sources for all PHY modes are
given in
Table2-8
. When a particular overhead field is set to be disabled, it will be
filled with 0s. Overhead generation is disabled dependent on mode, according to the
data in
Table3-6
.
Bit 12
0
0
0
0
Bit 11
0
0
1
1
Bit 10
0
1
0
1
0
1
0
1
BIP Field to be Errored
No errors inserted
B1 field (all modes)
B2 field, bits 23:16 (STS-3c/STM-1 mode only)
B2 field, bits 15:8 (STS-3c/STM-1 mode only)
B2 field, bits 7:0 (STS-1/STS-3c/STM-1 modes)
B3 field (STS-1/STS-3c/STM-1 modes)
No errors inserted
B2 field, all 3 octets (STS-3c/STM-1 mode)
相關PDF資料
PDF描述
CN8332EXF PCM Transceiver
CN8333EXF PCM Transceiver
CN8394KTF Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
CN8398KBG Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
CN8398KPF Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
相關代理商/技術參數
參數描述
CN8292-000 制造商:TE Connectivity 功能描述:222K174-25/225-0-CS8000 制造商:TE Connectivity 功能描述:222K174-25/225-0-CS8000 - Bulk
CN8293-000 功能描述:電纜固定件和配件 RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度:
CN8299-000 制造商:TE Connectivity 功能描述:TE3000-MEDIA-SENSOR - Bulk 制造商:TE Connectivity 功能描述:TTC-PRINTER-2000/3000-MEDIA SENSOR
CN8330 制造商:CONEXANT 制造商全稱:CONEXANT 功能描述:DS3/E3 Framer with 52 Mbps HDLC Controller
CN8330EPD 制造商:CONEXANT 制造商全稱:CONEXANT 功能描述:DS3/E3 Framer with 52 Mbps HDLC Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*