參數資料
型號: ARM60
廠商: Mitel Networks Corporation
英文描述: Low Power General Purpose 32-Bit RISC Microprocessor(低功耗通用32位精簡指令集微處理器)
中文描述: 低功耗通用32位RISC微處理器(低功耗通用32位精簡指令集微處理器)
文件頁數: 45/121頁
文件大?。?/td> 1217K
代理商: ARM60
Instruction Set - LDM, STM
41
4.8 Block data transfer (LDM, STM)
The instruction is only executed if the condition is true. The various conditions are defined at the beginning
of this chapter. The instruction encoding is shown in
Figure 18: Block Data Transfer Instructions
.
Block data transfer instructions are used to load (LDM) or store (STM) any subset of the currently visible
registers. They support all possible stacking modes, maintaining full or empty stacks which can grow up or
down memory, and are very efficient instructions for saving or restoring context, or for moving large blocks
of data around main memory.
4.8.1 The register list
The instruction can cause the transfer of any registers in the current bank (and non-user mode programs
can also transfer to and from the user bank, see below). The register list is a 16 bit field in the instruction,
with each bit corresponding to a register. A 1 in bit 0 of the register field will cause R0 to be transferred, a
0 will cause it not to be transferred; similarly bit 1 controls the transfer of R1, and so on.
Any subset of the registers, or all the registers, may be specified. The only restriction is that the register list
should not be empty.
Whenever R15 is stored to memory the stored value is the address of the STM instruction plus 12.
Figure 18: Block Data Transfer Instructions
4.8.2 Addressing modes
The transfer addresses are determined by the contents of the base register (Rn), the pre/post bit (P) and the
up/down bit (U). The registers are transferred in the order lowest to highest, so R15 (if in the list) will
always be transferred last. The lowest register also gets transferred to/from the lowest memory address. By
way of illustration, consider the transfer of R1, R5 and R7 in the case where Rn=0x1000 and write back of
Cond
Rn
0
15
16
19
20
21
24
25
27
28
31
P U
W L
22
23
100
S
Register list
Base register
Load/Store bit
1 = Load from memory
Write-back bit
1 = write address into base
PSR & force user bit
1 = load PSR or force user mode
Up/Down bit
1 = up; add offset to base
Pre/Post indexing bit
1 = pre; add offset before transfer
Condition field
相關PDF資料
PDF描述
ARM610 General Purpose 32-Bit Microprocessor with 4kByte Cache,Write Buffer and Memory Management Unit(通用32位微處理器(帶4K字節緩存,寫緩沖器和存儲器管理單元))
ARRAYS NIGHT VISION H.V. RECTIFIER DIODES & ARRAYS
ARS2540 40A GLASS PASSIVATED AVALANCHE BUTTON DIODE
AR2540 40A GLASS PASSIVATED AVALANCHE BUTTON DIODE
ARS25A 25A AUTOMOTIVE BUTTON DIODE
相關代理商/技術參數
參數描述
ARM607 制造商:Master Appliance Corp 功能描述:Armature, With Retaining Rings, 120V (HG 制造商:Master Appliance Corp 功能描述:Armature, With Retaining Rings, 120V (HG-751B)
ARM-607 制造商:Master Appliance Corp 功能描述:Nozzle Shield; HG-751B heat gun 制造商:Master Appliance 功能描述:Heat Gun,Armature W/Retaining Ring For Hg-751B 120V, Hg-501A-D
ARM610 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:General purpose 32-bit microprocessor
ARM7-009 制造商:Gravitech 功能描述:ARM7 LPC2378 W/2.8" TCH SCRN LCD BLU
ARM720T 制造商:未知廠家 制造商全稱:未知廠家 功能描述:General-purpose 32-bit Microprocessor with 8KB cache, enlarged Write buffer, and Memory Management Unit (MMU) combined in a single chip