參數資料
型號： ST7DALI
廠商： 意法半導體
元件分類： ADC
英文描述： 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI, DALI
中文描述： 8位單電壓閃存存儲器，數據EEPROM，模數轉換器，定時器，SPI和大理微控制器
文件頁數： 92/141頁
文件大小： 2175K
代理商： ST7DALI
ST7DALI
92/141
1
10-BIT A/D CONVERTER (ADC)
(Cont’d)
11.6.6 Register Description
CONTROL/STATUS REGISTER (ADCCSR)
Read/Write (Except bit 7 read only)
Reset Value: 0000 0000 (00h)
Bit 7 =
EOC
End of
Conversion
This bit is set by hardware. It is cleared by soft-
ware reading the ADCDRH register.
0: Conversion is not complete
1: Conversion complete
Bit 6 =
SPEED
ADC clock selection
This bit is set and cleared by software. It is used
together with the SLOW bit to configure the ADC
clock speed. Refer to the table in the SLOW bit de-
scription.
Bit 5 =
ADON
A/D Converter on
This bit is set and cleared by software.
0: A/D converter and amplifier are switched off
1: A/D converter and amplifier are switched on
Bit 4:3 =
Reserved.
Must be kept cleared.
Bit 2:0 =
CH[2:0]
Channel Selection
These bits are set and cleared by software. They
select the analog input to convert.
*The number of channels is device dependent. Refer to
the device pinout description.
DATA REGISTER HIGH (ADCDRH)
Read Only
Reset Value: xxxx xxxx (xxh)
Bit 7:0 =
D[9:2]
MSB of
Analog Converted Value
AMP CONTROL/DATA REGISTER LOW (AD-
CDRL)
Read/Write
Reset Value: 0000 00xx (0xh)
Bit 7:5 = Reserved. Forced by hardware to 0.
Bit 4 =
AMPCAL
Amplifier Calibration Bit
This bit is set and cleared by software. User is sug-
gested to use this bit to calibrate the ADC when
amplifier is ON. Setting this bit internally connects
amplifier input to 0v. Hence, corresponding ADC
output can be used in software to eliminate ampli-
fier-offset error.
0: Calibration off
1: Calibration on. (The input voltage of the amp is
set to 0V)
Note:
It is advised to use this bit to calibrate the
ADC when the amplifier is ON. Setting this bit in-
ternally connects the amplifier input to 0v. Hence,
the corresponding ADC output can be used in soft-
ware to eliminate an amplifier-offset error.
Bit 3 =
SLOW
Slow mode
This bit is set and cleared by software. It is used
together with the SPEED bit to configure the ADC
clock speed as shown on the table below.
7
0
EOC
SPEED ADON
0
CH3
CH2
CH1
CH0
Channel Pin*
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
CH2
0
0
0
0
1
1
1
CH1
0
0
1
1
0
0
1
CH0
0
1
0
1
0
1
0
7
0
D9
D8
D7
D6
D5
D4
D3
D2
7
0
0
0
0
AMP
CAL
SLOW
AMP-
SEL
D1
D0
f
ADC
f
CPU
/2
f
CPU
f
CPU
/4
SLOW SPEED
0
0
1
0
1
x
相關PDF資料
PDF描述
ST7FDALIF2M6 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI, DALI
ST7PDALIF2M6 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI, DALI
ST7FLCD1 8-bit MCU for LCD Monitors with 60 KBytes Flash, 2 KBytes RAM, 2 DDC Ports and Infrared Controller
ST7FLIT19B 8-Bit MCU With Single Voltage Flash Memory, Data EEPROM, ADC, 5 Timers, SPI(內部RC,PLL,ADC,ROP,ICP, IAP,SPI的8位MCU)
ST7FLITE10F1B6 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 4 TIMERS, SPI
相關代理商/技術參數
參數描述
ST7DALI-EVAL 功能描述:開發板和工具包 - 其他處理器 Eval for ST7DALI RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓:
ST7-DVP3 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost, Real Time Emulator Series for ST7
ST7EA 100 功能描述:微調電阻器 - 表面貼裝 ST7EA101 RoHS:否 制造商:Murata 產品:Single-Turn Trimmer Potentiometers 產品類型:Single Turn 轉數:1 元件類型:Cermet 錐度:Linear 電阻:10 kOhms 電壓額定值: 端接類型:SMD/SMT 功率額定值:250 mW (1/4 W) 容差:20 % 溫度系數:150 PPM / C
ST-7EA 100(101) 制造商:Copal Electronics 功能描述:100 }20% (B) }100ppm/ 0.25W/70 0W/125 6.4~3.4~6.1mm +125 -55 6.4mm 3.4mm 6.1mm
ST-7EA 100k(104) 制造商:Copal Electronics 功能描述:100k }20% (B) }100ppm/ 0.25W/70 0W/125 6.4~3.4~6.1mm +125 -55 6.4mm 3.4mm 6.1mm
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*