- 您現在的位置：買賣IC網 > PDF目錄382553 > ST7DALI (意法半導體) 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI, DALI PDF資料下載
參數資料
| 型號： | ST7DALI |
| 廠商： | 意法半導體 |
| 元件分類： | ADC |
| 英文描述： | 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI, DALI |
| 中文描述： | 8位單電壓閃存存儲器，數據EEPROM，模數轉換器，定時器，SPI和大理微控制器 |
| 文件頁數： | 23/141頁 |
| 文件大?。?/td> | 2175K |
| 代理商： | ST7DALI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁
ST7DALI
23/141
7 SUPPLY, RESET AND CLOCK MANAGEMENT
The device includes a range of utility features for
securing the application in critical situations (for
example in case of a power brown-out), and re-
ducing the number of external components.
Main features
■
Clock Management
– 1 MHz internal RC oscillator (enabled by op-
tion byte)
– 1 to 16 MHz or 32kHz External crystal/ceramic
resonator (selected by option byte)
– External Clock Input (enabled by option byte)
– PLL for multiplying the frequency by 8 or 4
(enabled by option byte)
– For clock ART counter only: PLL32 for multi-
plying the 8 MHz frequency by 4 (enabled by
option byte). The 8 MHz input frequency is
mandatory and can be obtained in the follow-
ing ways:
–1 MHz RC + PLLx8
–16 MHz external clock (internally divided
by 2)
–2 MHz. external clock (internally divided by
2) + PLLx8
–Crystal oscillator with 16 MHz output fre-
quency (internally divided by 2)
■
Reset Sequence Manager (RSM)
■
System Integrity Management (SI)
– Main supply Low voltage detection (LVD) with
reset generation (enabled by option byte)
– Auxiliary Voltage detector (AVD) with interrupt
capability for monitoring the main supply (en-
abled by option byte)
7.1 INTERNAL RC OSCILLATOR ADJUSTMENT
The device contains an internal RC oscillator with
an accuracy of 1% for a given device, temperature
and voltage range (4.5V-5.5V). It must be calibrat-
ed to obtain the frequency required in the applica-
tion. This is done by software writing a calibration
value in the RCCR (RC Control Register).
Whenever the microcontroller is reset, the RCCR
returns to its default value (FFh), i.e. each time the
device is reset, the calibration value must be load-
ed in the RCCR. Predefined calibration values are
stored in EEPROM for 3 and 5V V
DD
supply volt-
ages at 25°C, as shown in the following table.
Note:
– See “ELECTRICAL CHARACTERISTICS” on
page 100. for more information on the frequency
and accuracy of the RC oscillator.
– To improve clock stability, it is recommended to
place a decoupling capacitor between the V
DD
and V
SS
pins.
– These two bytes are systematically programmed
by ST, including on FASTROM devices. Conse-
quently, customers intending to use FASTROM
service must not use these two bytes.
– RCCR0 and RCCR1 calibration values will be
erased if the read-out protection bit is reset after
it has been set. See “Read out Protection” on
page 14.
Caution:
If the voltage or temperature conditions
change in the application, the frequency may need
to be recalibrated.
Refer to application note AN1324 for information
on how to calibrate the RC frequency using an ex-
ternal reference signal.
7.2 PHASE LOCKED LOOP
The PLL can be used to multiply a 1MHz frequen-
cy from the RC oscillator or the external clock by 4
or 8 to obtain f
OSC
of 4 or 8 MHz. The PLL is ena-
bled and the multiplication factor of 4 or 8 is select-
ed by 2 option bits.
– The x4 PLL is intended for operation with V
DD
in
the 2.4V to 3.3V range
– The x8 PLL is intended for operation with V
DD
in
the 3.3V to 5.5V range
Refer to
Section 15.1
for the option byte descrip-
tion.
If the PLL is disabled and the RC oscillator is ena-
bled, then f
OSC =
1MHz.
If both the RC oscillator and the PLL are disabled,
f
OSC
is driven by the external clock.
RCCR
Conditions
ST7DALI
Address
RCCR0
V
DD
=5V
T
A
=25°C
f
RC
=1MHz
V
DD
=3V
T
A
=25°C
f
RC
=700KHz
1000h
and FFDEh
RCCR1
1001h
and FFDFh
1
相關PDF資料 |
PDF描述 |
|---|---|
| ST7FDALIF2M6 | 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI, DALI |
| ST7PDALIF2M6 | 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI, DALI |
| ST7FLCD1 | 8-bit MCU for LCD Monitors with 60 KBytes Flash, 2 KBytes RAM, 2 DDC Ports and Infrared Controller |
| ST7FLIT19B | 8-Bit MCU With Single Voltage Flash Memory, Data EEPROM, ADC, 5 Timers, SPI(內部RC,PLL,ADC,ROP,ICP, IAP,SPI的8位MCU) |
| ST7FLITE10F1B6 | 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 4 TIMERS, SPI |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST7DALI-EVAL | 功能描述:開發板和工具包 - 其他處理器 Eval for ST7DALI RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
| ST7-DVP3 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost, Real Time Emulator Series for ST7 |
| ST7EA 100 | 功能描述:微調電阻器 - 表面貼裝 ST7EA101 RoHS:否 制造商:Murata 產品:Single-Turn Trimmer Potentiometers 產品類型:Single Turn 轉數:1 元件類型:Cermet 錐度:Linear 電阻:10 kOhms 電壓額定值: 端接類型:SMD/SMT 功率額定值:250 mW (1/4 W) 容差:20 % 溫度系數:150 PPM / C |
| ST-7EA 100(101) | 制造商:Copal Electronics 功能描述:100 }20% (B) }100ppm/ 0.25W/70 0W/125 6.4~3.4~6.1mm +125 -55 6.4mm 3.4mm 6.1mm |
| ST-7EA 100k(104) | 制造商:Copal Electronics 功能描述:100k }20% (B) }100ppm/ 0.25W/70 0W/125 6.4~3.4~6.1mm +125 -55 6.4mm 3.4mm 6.1mm |
發布緊急采購，3分鐘左右您將得到回復。