參數資料
型號： ST7DALI
廠商： 意法半導體
元件分類： ADC
英文描述： 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI, DALI
中文描述： 8位單電壓閃存存儲器，數據EEPROM，模數轉換器，定時器，SPI和大理微控制器
文件頁數： 49/141頁
文件大小： 2175K
代理商： ST7DALI
ST7DALI
49/141
I/O PORTS
(Cont’d)
Analog alternate function
Configure the I/O as floating input to use an ADC
input. The analog multiplexer (controlled by the
ADC registers) switches the analog voltage
present on the selected pin to the common analog
rail, connected to the ADC input.
Analog Recommendations
Do not change the voltage level or loading on any
I/O while conversion is in progress. Do not have
clocking pins located close to a selected analog
pin.
WARNING
: The analog input voltage level must
be within the limits stated in the absolute maxi-
mum ratings.
10.3 I/O PORT IMPLEMENTATION
The hardware implementation on each I/O port de-
pends on the settings in the DDR and OR registers
and specific I/O port features such as ADC input or
open drain.
Switching these I/O ports from one state to anoth-
er should be done in a sequence that prevents un-
wanted side effects. Recommended safe transi-
tions are illustrated in
Figure 31
. Other transitions
are potentially risky and should be avoided, since
they may present unwanted side-effects such as
spurious interrupt generation.
Figure 31. Interrupt I/O Port State Transitions
10.4 UNUSED I/O PINS
Unused I/O pins must be connected to fixed volt-
age levels. Refer to
Section 13.8
.
10.5 LOW POWER MODES
10.6 INTERRUPTS
The external interrupt event generates an interrupt
if the corresponding configuration is selected with
DDR and OR registers and if the I bit in the CC
register is cleared (RIM instruction).
Mode
Description
WAIT
No effect on I/O ports. External interrupts
cause the device to exit from WAIT mode.
No effect on I/O ports. External interrupts
cause the device to exit from HALT mode.
HALT
Interrupt Event
Event
Flag
Enable
Control
Bit
Exit
from
Wait
Exit
from
Halt
External interrupt on
selected external
event
-
DDRx
ORx
Yes
Yes
01
floating/pull-up
interrupt
INPUT
00
floating
(reset state)
INPUT
10
open-drain
OUTPUT
11
push-pull
OUTPUT
XX
= DDR, OR
1
相關PDF資料
PDF描述
ST7FDALIF2M6 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI, DALI
ST7PDALIF2M6 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI, DALI
ST7FLCD1 8-bit MCU for LCD Monitors with 60 KBytes Flash, 2 KBytes RAM, 2 DDC Ports and Infrared Controller
ST7FLIT19B 8-Bit MCU With Single Voltage Flash Memory, Data EEPROM, ADC, 5 Timers, SPI(內部RC,PLL,ADC,ROP,ICP, IAP,SPI的8位MCU)
ST7FLITE10F1B6 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 4 TIMERS, SPI
相關代理商/技術參數
參數描述
ST7DALI-EVAL 功能描述:開發板和工具包 - 其他處理器 Eval for ST7DALI RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓:
ST7-DVP3 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost, Real Time Emulator Series for ST7
ST7EA 100 功能描述:微調電阻器 - 表面貼裝 ST7EA101 RoHS:否 制造商:Murata 產品:Single-Turn Trimmer Potentiometers 產品類型:Single Turn 轉數:1 元件類型:Cermet 錐度:Linear 電阻:10 kOhms 電壓額定值: 端接類型:SMD/SMT 功率額定值:250 mW (1/4 W) 容差:20 % 溫度系數:150 PPM / C
ST-7EA 100(101) 制造商:Copal Electronics 功能描述:100 }20% (B) }100ppm/ 0.25W/70 0W/125 6.4~3.4~6.1mm +125 -55 6.4mm 3.4mm 6.1mm
ST-7EA 100k(104) 制造商:Copal Electronics 功能描述:100k }20% (B) }100ppm/ 0.25W/70 0W/125 6.4~3.4~6.1mm +125 -55 6.4mm 3.4mm 6.1mm
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*