參數資料
型號： S71PL191HB0BFI100
廠商： SPANSION LLC
元件分類： 存儲器
英文描述： SPECIALTY MEMORY CIRCUIT, PBGA73
封裝： 9 X 13 MM, LEAD FREE, FBGA-73
文件頁數： 18/172頁
文件大?。?/td> 4662K
代理商： S71PL191HB0BFI100
18
S29JL064H
S29JL064HA1 May 7, 2004
Pr el i m i n ary
Sector protect/Sector Unprotect requires VID on the RESET# pin only, and can be
implemented either in-system or via programming equipment. Figure 2 shows
the algorithms and Figure 26 shows the timing diagram. For sector unprotect, all
unprotected sectors must first be protected prior to the first sector unprotect
write cycle. Note that the sector unprotect algorithm unprotects all sectors in par-
allel. All previously protected sectors must be individually re-protected. To
change data in protected sectors efficiently, the temporary sector unprotect func-
The device is shipped with all sectors unprotected. Optional Spansion program-
ming service enable programming and protecting sectors at the factory prior to
shipping the device. Contact your local sales office for details.
It is possible to determine whether a sector is protected or unprotected. See the
Autoselect Mode section for details.
Write Protect (WP#)
The Write Protect function provides a hardware method of protecting without
using VID. This function is one of two provided by the WP#/ACC pin.
If the system asserts VIL on the WP#/ACC pin, the device disables program and
erase functions in sectors 0, 1, 140, and 141, independently of whether those
sectors were protected or unprotected using the method described in “Sector/
If the system asserts VIH on the WP#/ACC pin, the device reverts to whether sec-
tors 0, 1, 140, and 141 were last set to be protected or unprotected. That is,
sector protection or unprotection for these sectors depends on whether they were
last protected or unprotected using the method described in “Sector/Sector Block
Note that the WP#/ACC pin must not be left floating or unconnected; inconsistent
behavior of the device may result.
Table 6. WP#/ACC Modes
Temporary Sector Unprotect
(Note: For the following discussion, the term “sector” applies to both sectors and
sector blocks. A sector block consists of two or more adjacent sectors that are
protected or unprotected at the same time (see Table 5).
This feature allows temporary unprotection of previously protected sectors to
change data in-system. The Temporary Sector Unprotect mode is activated by
setting the RESET# pin to
VID. During this mode, formerly protected sectors can
be programmed or erased by selecting the sector addresses. Once VID is removed
from the RESET# pin, all the previously protected sectors are protected again.
shows the algorithm, and 25 shows the timing diagrams, for this feature. If the
WP#/ACC pin is at VIL, sectors 0, 1, 140, and 141 will remain protected during
the Temporary sector Unprotect mode.
WP# Input Voltage
Device
Mode
VIL
Disables programming and erasing in SA0, SA1, SA140, and SA141
VIH
Enables programming and erasing in SA0, SA1, SA140, and SA141, dependent on
whether they were last protected or unprotected.
VHH
Enables accelerated progamming (ACC). See “Accelerated Program Operation” on
相關PDF資料
PDF描述
S71VS128RC0ZHK203 SPECIALTY MEMORY CIRCUIT, PBGA56
S71VS128RC0ZHK2L2 SPECIALTY MEMORY CIRCUIT, PBGA56
S71WS512ND0BAWEH SPECIALTY MEMORY CIRCUIT, PBGA84
S72NS512PE0AHGL02 SPECIALTY MEMORY CIRCUIT, PBGA133
S7911 PIN PHOTO DIODE
相關代理商/技術參數
參數描述
S71PL254 制造商:SPANSION 制造商全稱:SPANSION 功能描述:STACKED MULTI CHIP PRODUCT FLASH MEMORY AND RAM
S71PL254J 制造商:SPANSION 制造商全稱:SPANSION 功能描述:STACKED MULTI CHIP PRODUCT FLASH MEMORY AND RAM
S71PL254J04BAW0Z0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Based MCPs
S71PL254J04BAW0Z2 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Based MCPs
S71PL254J04BAW0Z3 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Based MCPs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*