- 您現在的位置：買賣IC網 > PDF目錄11744 > PI7C8150AMAE (Pericom)IC PCI-PCI BRIDGE 2PORT 208-FQFP PDF資料下載
參數資料
| 型號： | PI7C8150AMAE |
| 廠商： | Pericom |
| 文件頁數： | 73/111頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PCI-PCI BRIDGE 2PORT 208-FQFP |
| 標準包裝： | 24 |
| 系列： | * |
| 應用： | * |
| 接口： | * |
| 電源電壓： | * |
| 封裝/外殼： | 208-BFQFP |
| 供應商設備封裝： | 208-FQFP（28x28） |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁當前第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁
PI7C8150A
2-PORT PCI-TO-PCI BRIDGE
Page 64 of 111
APRIL 2006 – Revision 1.1
established between 2 ports or the target bus is already locked by another master, then the
current lock cycle is retried without forward. Because a target retry is signaled to the
initiator, the initiator must relinquish the lock on the primary bus, and therefore the lock is
not yet established.
The first locked transaction must be a memory read transaction. Subsequent locked
transactions can be memory read or memory write transactions. Posted memory write
transactions that are a part of the locked transaction sequence are still posted. Memory read
transactions that are a part of the locked transaction sequence are not pre-fetched.
When the locked delayed memory read request is queued, PI7C8150A does not queue any
more transactions until the locked sequence is finished. PI7C8150A signals a target retry to
all transactions initiated subsequent to the locked read transaction that are intended for
targets on the other side of PI7C8150A. PI7C8150A allows any transactions queued before
the locked transaction to complete before initiating the locked transaction.
When the locked delayed memory read request transaction moves to the head of the
delayed transaction queue, PI7C8150A initiates the transaction as a locked read transaction
by de-asserting LOCK_L on the target bus during the first address phase, and by asserting
LOCK_L one cycle later. If LOCK_L is already asserted (used by another initiator),
PI7C8150A waits to request access to the secondary bus until LOCK_L is de-asserted
when the target bus is idle. Note that the existing lock on the target bus could not have
crossed PI7C8150A. Otherwise, the pending queued locked transaction would not have
been queued. When PI7C8150A is able to complete a data transfer with the locked read
transaction, the lock is established on the secondary bus.
When the initiator repeats the locked read transaction on the primary bus with the same
address, transaction type, and byte enable bits, PI7C8150A transfers the read data back to
the initiator, and the lock is then also established on the primary bus.
For PI7C8150A to recognize and respond to the initiator, the initiator’s subsequent
attempts of the read transaction must use the locked transaction sequence (de-assert
LOCK_L during address phase, and assert LOCK_L one cycle later). If the LOCK_L
sequence is not used in subsequent attempts, a master timeout condition may result. When
a master timeout condition occurs, SERR_L is conditionally asserted (see Section 6.4), the
read data and queued read transaction are discarded, and the LOCK_L signal is de-asserted
on the target bus.
Once the intended target has been locked, any subsequent locked transactions initiated on
the initiator bus that are forwarded by PI7C8150A are driven as locked transactions on the
target bus.
The first transaction to establish LOCK_L must be Memory Read. If the first transaction is
not Memory read, the following transactions behave accordingly:
Type 0 Configuration Read/Write induces master abort
Type 1 Configuration Read/Write induces master abort
I/O Read induces master abort
I/O Write induces master abort
06-0057
相關PDF資料 |
PDF描述 |
|---|---|
| PIC18F2515-I/SP | IC MCU FLASH 24KX16 28-DIP |
| V300A15E500B2 | CONVERTER MOD DC/DC 15V 500W |
| PIC16C73B-04I/SO | IC MCU OTP 4KX14 A/D PWM 28SOIC |
| GRM1555C1H301JA01D | CAP CER 300PF 50V 5% NP0 0402 |
| PIC16LF876A-I/ML | IC PIC MCU FLASH 8KX14 28QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI7C8150AMAE-33 | 功能描述:外圍驅動器與原件 - PCI 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8150AND | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:2-PORT PCI-to-PCI BRIDGE |
| PI7C8150AND-33 | 制造商:Pericom Semiconductor Corporation 功能描述:PCI-TO-PCI BRIDGE 256BGA - Rail/Tube |
| PI7C8150ANDE | 功能描述:外圍驅動器與原件 - PCI 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8150B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCI Bridge | Asynchronous 2-Port PCI Bridge |
發布緊急采購，3分鐘左右您將得到回復。