- 您現在的位置：買賣IC網 > PDF目錄367801 > PC8245MTPU300D (ATMEL CORP) Integrated Processor Family PDF資料下載
參數資料
| 型號： | PC8245MTPU300D |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Integrated Processor Family |
| 中文描述： | 32-BIT, 300 MHz, RISC PROCESSOR, PBGA352 |
| 封裝： | 35 X 35 MM, 1.27 MM PITCH, TBGA-352 |
| 文件頁數： | 50/61頁 |
| 文件大小： | 429K |
| 代理商： | PC8245MTPU300D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
50
PC8245
2171D–HIREL–06/04
In addition, it is recommended that there be several bulk storage capacitors distributed
around the PCB, feeding the
V
DD
, O
V
DD
, G
V
DD
, and L
V
DD
planes, to enable quick recharg-
ing of the smaller chip capacitors. These bulk capacitors should have a low ESR
(equivalent series resistance) rating to ensure the quick response time necessary. They
should also be connected to the power and ground planes through two vias to minimize
inductance. Suggested bulk capacitors: 100 – 330 μF (AVX TPS tantalum or Sanyo
OSCON).
Connection
Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an
appropriate signal level. Unused active-low inputs should be tied to O
V
DD
. Unused
active-high inputs should be connected to GND. All NC (no connect) signals must
remain unconnected.
Power and ground connections must be made to all external
V
DD
, O
V
DD
, G
V
DD
, L
V
DD
, and
GND pins of the PC8245.
The PCI_SYNC_OUT signal is intended to be routed halfway out to the PCI devices and
then returned to the PCI_SYNC_IN input of the PC8245.
The SDRAM_SYNC_OUT signal is intended to be routed halfway out to the SDRAM
devices and then returned to the SDRAM_SYNC_IN input of the PC8245. The trace
length may be used to skew or adjust the timing window as needed. See Motorola appli-
cation notes AN1849/D and AN2164/D for more information on this topic. Note that
there is an SDRAM_SYNC_IN to PCI_SYNC_IN time requirement. (See Table 9 on
page 31.)
Pull-up/Pull-down Resistor
Requirements
The data bus input receivers are normally turned off when no read operation is in
progress; therefore, they do not require pull-up resistors on the bus. The data bus sig-
nals are: MDH[0:31], MDL[0:31], and PAR[0:7].
If the 32-bit data bus mode is selected, the input receivers of the unused data and parity
bits (MDL[0:31] and PAR[4:7]) will be disabled, and their outputs will drive logic zeros
when they would otherwise normally be driven. For this mode, these pins do not require
pull-up resistors and should be left unconnected by the system to minimize possible out-
put switching.
The TEST0 pin requires a pull-up resistor of 120
or less connected to O
V
DD
.
It is recommended that RTC have weak pull-up resistors (2 k
– 10 k
) connected to
G
V
DD
_O
V
DD
.
It is recommended that the following signals be pulled up to O
V
DD
with weak pull-up
resistors (2 k
– 10 k
): SDA, SCL, SMI, SRESET/SDMA12, TBEN/SDMA13,
CHKSTOP_IN/SDMA14, TRIG_IN/RCS2, and DRDY.
It is recommended that the following PCI control signals be pulled up to L
V
DD
with weak
pull-up resistors (2 k
– 10 k
): DEVSEL, FRAME, IRDY, LOCK, PERR, SERR, STOP,
and TRDY. The resistor values may need to be adjusted stronger to reduce induced
noise on specific board designs.
The following pins have internal pull-up resistors enabled at all times: REQ[3:0],
REQ4/DA4, TCK, TDI, TMS, and TRST. See Table 1 on page 6 for more information.
The following pins have internal pull-up resistors enabled only while device is in the
reset state:
GNT4/DA5, MDL0, FOE, RCS0, SDRAS, SDCAS, CKE, AS, MCP, MAA[0:2],
PMAA[0:2], and QACK/DA0. See Table 1 on page 6 for more information.
相關PDF資料 |
PDF描述 |
|---|---|
| PC8245MTPU333D | Integrated Processor Family |
| PC824A | NPN-OUTPUT DC-INPUT OPTOCOUPLER |
| PC844A | NPN-OUTPUT AC-INPUT OPTOCOUPLER |
| PC844X | PHOTOCOUPLER |
| PC844 | DEVICE SPECIFICATION FOR PHOTOCOUPLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PC8245MTPU333D | 制造商:e2v Aerospace & Defense 功能描述:MPU MPC82xx RISC 32-Bit 0.25um 333MHz 3.3V 352-Pin TBGA 制造商:e2v technologies 功能描述:MPU MPC82XX RISC 32BIT 0.25UM 333MHZ 3.3V 352TBGA - Trays |
| PC8245MTPU350D | 制造商:e2v technologies 功能描述:PC8245MTPU350D - Trays |
| PC824A | 功能描述:PHOTOCOUPLER 2CH AC INPUT 8-DIP RoHS:否 類別:隔離器 >> 光隔離器 - 晶體管，光電輸出 系列:- 標準包裝:1,000 系列:- 通道數:2 輸入類型:DC 電壓 - 隔離:2500Vrms 電流傳輸比（最小值）:7% @ 16mA 電流傳輸比（最大）:50% @ 16mA 輸出電壓:20V 電流 - 輸出 / 通道:8mA 電流 - DC 正向(If):25mA Vce飽和（最大）:- 輸出類型:有 Vcc 的晶體管 安裝類型:通孔 封裝/外殼:8-DIP（0.400"，10.16mm） 包裝:管件 其它名稱:HCPL-2530W |
| PC825 | 功能描述:PHOTOCOUPLER 2CH DARL OUT 8-DIP RoHS:否 類別:隔離器 >> 光隔離器 - 晶體管，光電輸出 系列:- 標準包裝:1,000 系列:- 通道數:2 輸入類型:DC 電壓 - 隔離:2500Vrms 電流傳輸比（最小值）:7% @ 16mA 電流傳輸比（最大）:50% @ 16mA 輸出電壓:20V 電流 - 輸出 / 通道:8mA 電流 - DC 正向(If):25mA Vce飽和（最大）:- 輸出類型:有 Vcc 的晶體管 安裝類型:通孔 封裝/外殼:8-DIP（0.400"，10.16mm） 包裝:管件 其它名稱:HCPL-2530W |
| PC-825 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:High Sensitivity High Density Mounting Type Photocoupler(232.40 k) |
發布緊急采購，3分鐘左右您將得到回復。